618150
405
Zoom out
Zoom in
Previous page
1/428
Next page
TROUBLESHOOTING
403
10
Appendix
After sewing
Problem Cause Solution Page
Thread tension is
incorrect.
Upper threading is incorrect. Check the steps for threading the machine and
rethread the machine.
62
Bobbin is set incorrectly. Reset the bobbin. (If needle plate was
removed, reinstall needle plate and tighten
screws prior to installing bobbin case.)
59
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combinations” chart.
77
Presser foot holder is not attached correctly. Reattach the presser foot holder correctly. 71
Thread tension is set incorrectly. Adjust the thread tension. 92, 301
Bobbin thread is incorrectly wound. Use a correctly wound bobbin. 54
Needle is turned, bent or the point is dull. Replace the needle. 75
A bobbin designed specifically for this
machine is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
59
Character or
decorative patterns
are misaligned.
Pattern adjustment settings were set
incorrectly.
Revise the pattern adjustment settings. 176
Pattern does not turn
out.
Wrong presser foot was used. Attach the correct presser foot. “STITCH SETTING
CHART”
Did not use a stabilizer material on thin fabrics
or stretch fabrics.
Attach a stabilizer material. 175
Thread tension is set incorrectly. Adjust the thread tension. 92, 301
Fabric was pulled, pushed or fed at an angle
while it was being sewn.
Sew while guiding the fabric with your hands
so that the fabric is fed in a straight line.
82
The thread is tangled, for example, in the
bobbin case.
Remove the tangle thread. If the thread is
tangled in the bobbin case, clean the race.
Embroidery pattern
does not sew out
correctly.
Thread is twisted. Use scissors, etc., to cut the twisted thread
and remove it from the bobbin case, etc.
Thread tension is set incorrectly. Adjust the thread tension. 92, 301
Fabric was not inserted into the frame
correctly (fabric was loose, etc.).
If the fabric is not stretched tight in the frame,
the pattern may turn out poorly or there may
be shrinkage of the pattern. Set the fabric into
the frame correctly.
258
Stabilizing material was not attached. Always use stabilizing material, especially with
stretch fabrics, lightweight fabrics, fabrics with
a coarse weave, or fabrics that often cause
pattern shrinkage. See your authorized Brother
dealer for the proper stabilizer.
256
There was an object placed near the machine,
and the carriage or embroidery frame hit the
object during sewing.
If the frame bumps something during sewing,
the pattern will turn out poorly. Do not place
anything in the area where the frame may
bump it during sewing.
273
Fabric outside the frame edges interferes with
the sewing arm, so the embroidery unit cannot
move.
Reinsert the fabric in the embroidery frame so
that the excess fabric is away from the sewing
arm, and rotate the pattern 180 degrees.
258
Fabric is too heavy, so the embroidery unit
cannot move freely.
Place a large thick book or similar object under
the arm head to lightly lift the heavy side and
keep it level.
Fabric is hanging off the table. If the fabric is hanging off the table during
embroidery, the embroidery unit will not move
freely. Place the fabric so that it does not hang
off the table or hold the fabric to keep it from
dragging.
273
Fabric is snagged or caught on something. Stop the machine and place the fabric so that
it does not get caught or snagged.
Embroidery frame was removed during sewing
(for example, to reset the bobbin). The presser
foot was bumped or moved while removing or
attaching the embroidery frame, or the
embroidery unit was moved.
If the presser foot is bumped or the
embroidery unit is moved during sewing, the
pattern will not turn out. Be careful when
removing or reattaching the embroidery frame
during sewing.
280
Stabilizer is incorrectly attached, for example,
it is smaller than the embroidery frame.
Attach the stabilizer correctly. 256
405


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is XV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is XV in the language / languages: English as an attachment in your email.

The manual is 23,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is XV

Brother Innov-is XV User Manual - German - 420 pages

Brother Innov-is XV User Manual - Dutch - 420 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info