618150
404
Zoom out
Zoom in
Previous page
1/428
Next page
TROUBLESHOOTING
402
Skipped stitches Needle is turned, bent or the point is dull. Replace the needle. 75
Needle is installed incorrectly. Reinstall the needle correctly. 75
Needle is defective. Replace the needle. 75
Dust or lint has collected under the needle
plate.
Remove the dust or lint with the brush. 388
Thin or stretch fabrics are being sewn. Sew with one sheet of thin paper under the
fabric.
89
No stitching Needle is turned, bent or the point is dull. Replace the needle. 75
Bobbin is set incorrectly. Reset the bobbin thread correctly. 59
Upper threading is incorrect. Check the steps for threading the machine and
rethread the machine.
62
High-pitched sound
while sewing
Dust or lint is caught in the feed dogs. Remove the dust or lint. 388
Pieces of thread are caught in the race. Clean the race. 388
Upper threading is incorrect. Check the steps for threading the machine and
rethread the machine.
62
A bobbin designed specifically for this
machine is not used.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
59
There are needle holes or friction scratches in
the bobbin case.
Replace the bobbin case, or consult your
authorized Brother dealer.
388
Fabric does not feed
through the machine.
Feed dogs are set in the down position.
Press , and then turn the handwheel to
raise the feed dogs.
133
Stitches are too close together. Lengthen the stitch length setting. 91
Wrong presser foot was used. Use the correct presser foot.
“STITCH SETTING
CHART”
Needle is turned, bent or the point is dull. Replace the needle. 75
Thread is entangled. Cut the entangled thread and remove it from
the race.
Zigzag foot “J” is slanted on a thick seam at
the beginning of stitching.
Use the presser foot locking pin (black button
on the left side) on zigzag foot “J” to keep the
presser foot level while sewing.
88
The fabric feeds in
the opposite
direction.
The feed mechanism is damaged. Contact your authorized Brother dealer.
The needle contacts
the needle plate.
The needle clamp screw is loose. Firmly tighten the needle clamp screw. If the
needle is bent or blunt, replace it with a new
one.
75
Needle is turned, bent or the point is dull. Replace the needle. 75
Fabric being sewn
with the machine
cannot be removed.
Thread is tangled below the needle plate. Lift up the fabric and cut the threads below it,
and clean the race.
393
A broken needle has
fallen into the
machine.
Turn off the machine, and then remove the
needle plate. If the needle that fell into the
machine can be seen, use tweezers to remove
it. After removing the needle, return the needle
plate to its original position.
Before turning on the machine, slowly turn the
handwheel toward you to check that it turns
smoothly. If the handwheel does not turn
smoothly or the needle that fell into the
machine cannot be removed, consult your
authorized Brother dealer.
The handwheel feels
sluggish when it is
turned.
Thread is tangled in the bobbin case. Remove the tangled thread from the bobbin
case. Re-install the bobbin case so it is
correctly positioned.
393
Problem Cause Solution Page
404


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is XV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is XV in the language / languages: English as an attachment in your email.

The manual is 23,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is XV

Brother Innov-is XV User Manual - German - 420 pages

Brother Innov-is XV User Manual - Dutch - 420 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info