718769

Brother Innov-is M280D Manual

65
Zoom out
Zoom in
Previous page
1/100
Next page
Embroidering Preparation
63
EMBROIDERY
4
a
Loosen the embroidery frame adjustment screw and
remove the inner and outer frames, placing the outer
frame on a flat surface.
Separate the inner and outer frame by removing inner
frame upward.
b
Place the fabric with the stabilizer material on top of
the outer frame.
Have the right side of the fabric facing up.
c
Press the inner frame in from the top of the fabric.
Line up on the inner frame and on outer frame.
d
Tighten the adjustment screw by hand just enough to
secure the fabric.
e
Gently remove the fabric from the frame without
loosening the adjustment screw.
f
Press the inner frame in from the top of the fabric
again, lining up on the inner frame and on
outer frame.
• Press the inner frame into the outer frame.
g
Tighten the adjustment screw while removing any slack
in the fabric by hand. The goal is to have a drum-like
sound when the fabric is struck lightly.
■ Using the embroidery sheet
When you want to embroider the pattern in a particular
place, use the embroidery sheet with the frame.
a
With a chalk pencil, mark the area of the fabric you
want to embroider.
b
Place the embroidery sheet on the inner frame.
c
Line the mark on the fabric up with the base line on the
embroidery sheet.
d
Place the inner frame with the fabric on the outer
frame and adjust the fabric if needed to align marks on
fabric with the embroidery sheet.
• For details, refer to page 62.
e
Remove the embroidery sheet.
1 Inner frame
2 Outer frame
3 Adjustment screw
Memo
• This precautionary step will help reduce pattern
distortion while embroidering.
a
b
c
… 65 …


Need help? Post your question in this forum.

Forumrules
1

Forum

brother-innov-is-m280d

Reset search

  • bonjour
    je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03

    Reply Report abuse

  • bonjour
    je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
    Merci bonne journée Submitted on 3-9-2022 at 10:38

    Reply Report abuse

  • message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is M280D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info