Manual Brother Innov-is M280D (page 52 of 100) (English)

718769

Zoom out

Zoom in

1/100

Utility stitches

Other Stitching Applications

■ Elastic attaching

When elastic tape is attached to the cuff or waist of a piece of

clothing, the finished dimensions will be that of the stretched

elastic tape. Therefore, it is necessary that a suitable length of

the elastic tape be used.

Pin the elastic tape to the wrong side of the fabric.

Pin the elastic tape to the fabric at a few points to make

sure that the tape is uniformly positioned on the fabric.

Attach zigzag foot “J”.

Select a stitch.

• For details, refer to “Stitch Chart” on page 35.

Sew the elastic tape to the fabric while stretching the

tape so that it is the same length as the fabric.

While pulling the fabric behind the presser foot with

your left hand, pull the fabric at the pin nearest the front

of the presser foot with your right hand.

■ Bar tack stitching

Bar tacks are used to reinforce points subject to strain, such as

pocket corners and openings.

As an example, the procedure for sewing bar tacks at pocket

corners is described below.

Determine the desired length of the bar tack.

Set the button guide plate on buttonhole foot “A” to the

desired length. (The distance between the markings on

the presser foot scale is 5 mm (3/16 inch).)

• A bar tack with a maximum length of about 28 mm

(1–1/8 inches) can be sewn.

Attach buttonhole foot “A”.

Position the upper thread under the presser foot by

guiding thread through the hole in the presser foot

before attaching the buttonhole foot “A”.

Select a stitch.

• For details, refer to “Stitch Chart” on page 35.

Position the fabric so that the opening of the pocket

faces toward you, and then lower the presser foot lever

so that the needle drops 2 mm (1/16 inch) in front of

the pocket opening.

Pull down the buttonhole lever as far as possible.

Gently hold the end of the upper thread in your left

hand, and then start sewing.

After sewing is finished, raise the presser foot lever,

remove the fabric, and then cut the threads.

Raise the buttonhole lever to its original position.

No. 1-11 1-12 2-13

Stitch

CAUTION

• When sewing, be sure that the needle does not

touch any pins, otherwise the needle may bend

or break.

1 Presser foot scale

2 Length of bar tack

3 5 mm (3/16 inch)

No. 4-13

Stitch

1 2 mm (1/16 inch)

bonjour
je dois faire des coutures au point droit à 5mm du bord. comment faire le réglage. Merci Submitted on 15-11-2022 at 10:03
Reply Report abuse
bonjour
je souhaite faire des coutures à 0.5 cm avec ma brother 280. Comment faire
Merci bonne journée Submitted on 3-9-2022 at 10:38
Reply Report abuse
message sur brother 280 lorsque la commande de vitesse est réglée pour contrôler la largeur du point zigzag, la touche marche/arrêt ne fonctionne pas. Comment faire pour annuler cette commande Merci de m'aider Submitted on 27-5-2022 at 07:10
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is M280D in the language / languages: English as an attachment in your email.

The manual is 5,05 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is M280D

Brother Innov-is M280D User Manual - German - 100 pages

Brother Innov-is M280D User Manual - Dutch - 100 pages

Brother Innov-is M280D User Manual - French - 100 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brother Innov-is M280D Manual

Product: