718715
67
Zoom out
Zoom in
Previous page
1/72
Next page
Troubleshooting
65
APPENDIX
4
Error messages
When erroneous operations are performed messages and advice on operation will be displayed on the LCD. Follow what is
displayed. The error message will disappear if an operation button is pressed or the correct operation is performed while the error
message is displayed.
Operation beeps
If a correct operation is performed, the machine beeps one time.
If an incorrect operation is performed, the machine beeps two or four times.
If the machine locks up, for example, because the thread is tangled, the machine continues to beep for seven seconds, and then
the machine automatically stops. Be sure to check for the cause of the error, and correct it before continuing to sew.
Error Messages
Cause Solution
80/60/50 stitches
models
16 stitches model
This message is displayed when a button,
such as the “Start/Stop” button, is pressed
(The foot controller was depressed if it is
connected.) while the presser foot was
raised.
Lower the presser foot lever before
continuing the operation.
This message is displayed when the
buttonhole lever is down, a stitch other than a
buttonhole is selected, presser foot is
lowered and a button, such as the “Start/
Stop” button, is pressed (The foot controller
was depressed if it is connected.).
Raise the buttonhole lever before continuing
the operation.
This message is displayed when the
buttonhole lever is up, a buttonhole stitch is
selected, presser foot is lowered and a
button, such as the “Start/Stop” button, is
pressed (The foot controller was depressed if
it is connected.).
Lower the buttonhole lever before continuing
the operation.
This message is displayed when a button,
such as the Reverse stitch button, is pressed
while the bobbin winder shaft is moved to the
right.
Move the bobbin winder shaft to the left
before continuing the operation.
This message is displayed when the “Start/
Stop” button is pressed while the foot
controller is connected.
Disconnect the foot controller, and then press
the “Start/Stop” button. Otherwise, operate
the machine by using the foot controller.
The motor locked up because the thread
became tangled.
Clean the race to remove the tangled thread
(page 55).
After cleaning the race, insert the bobbin
case properly. If the needle is bent or broken,
replace the needle. Then, thread the upper
and bobbin threads properly, and continue
the operation.
This message is displayed when the needle
mode selection key is pressed while a stitch that
cannot be used with the twin needle is selected.
Select a stitch that can be used with the twin
needle.
This message is displayed when (Twin
needle) is turned on, and a stitch pattern that
cannot be sewn with the twin needle is
selected.
Switch to the single needle mode, and
replace the twin needle with a single needle
before continuing the operation.
This message is displayed when the needle
plate cover is removed while the machine is
still turned on.
Turn off the machine, and then attach the
needle plate cover before continuing the
operation.
F* F*
If error message “F*” appears in the LCD
while the machine is being used, the machine
may be malfunctioning.
(“*” will be replaced with a number.)
Contact your nearest Brother authorized
service center.
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is A80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is A80 in the language / languages: English as an attachment in your email.

The manual is 27,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is A80

Brother Innov-is A80 User Manual - German - 72 pages

Brother Innov-is A80 User Manual - Dutch - 72 pages

Brother Innov-is A80 User Manual - French - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info