463623
227
Zoom out
Zoom in
Previous page
1/249
Next page
TROUBLESHOOTING
216
Needle breaks Needle is installed incorrectly. Reinstall the needle correctly. 34
Needle clamp screw is not tightened. Tighten the needle clamp screw. 35
Needle is turned or bent. Replace the needle. 34
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combination” chart.
36
Wrong presser foot was used. Use the recommended presser foot. “STITCH SETTING
CHART”
Upper thread tension is too strong. Adjust the thread tension setting. 43, 154
Fabric is pulled during sewing. Do not pull the fabric during sewing.
Spool cap is set incorrectly. Check the method for attaching the spool cap,
then reattach the spool cap.
25
There are scratches around the holes in the
needle plate.
Replace the needle plate, or consult your
authorized dealer.
55
There are scratches around the hole(s) in the
presser foot.
Replace the presser foot, or consult your
authorized dealer.
32
There are scratches on the race. Replace the race, or consult your authorized
dealer.
210
Needle is defective. Replace the needle. 34
Fabric does not feed
through the machine
Feed dogs are set in the down position. Use the feed dog position lever to raise the
feed dogs.
71
Stitches are too close together. Lengthen the stitch length setting. 42
Wrong presser foot was used. Use the correct presser foot. “STITCH SETTING
CHART”
Needle is turned, bent or the point is dull. Replace the needle. 34
Thread is entangled. Cut the entangled thread and remove it from
the race.
Machine does not
operate
There is no pattern selected. Select a pattern. 48, 98, 130, 177
“Start/Stop” button was not pushed. Press the “Start/Stop” button. 3
Main power switch is not turned on. Turn the main power to ON. 8
Presser foot is not lowered. Lower the presser foot. 3
“Start/Stop” button was pushed with the foot
controller attached.
Remove the foot controller, or use the foot
controller to operate the machine.
39
Speed control lever is set to control the zigzag
stitch width.
Use the foot controller instead of the “Start/
Stop” button to operate the machine.
39
All keys and buttons have been locked by
.
Press to unlock all keys and
buttons.
32, 34
Embroidery unit does
not operate
There is no pattern selected. Select a pattern. 130, 177
Main power switch is not turned on. Turn the main power to ON. 8
Embroidery unit is not attached correctly. Reattach the embroidery unit correctly. 128
Embroidery frame was attached before the unit
was initialized.
Perform the initialization process correctly. 128
LCD display is difficult
to see
LCD contrast is not properly adjusted. Adjust the LCD contrast. 15, 212
Nothing happens,
even if the LCD
display is pressed
The screen has been locked. Press either of the following keys to unlock the
screen.
Problem Cause Solution Page
CAUTION
This machine is equipped with a thread detection device. If the “Start/Stop” button is pushed before the
upper threading is done, the machine will not operate properly. Also, depending on the pattern selected,
the machine may feed the fabric even if the needle is raised. This is due to the needle bar release
mechanism. At these times, the machine will make a sound different from that made during normal
sewing. This is not the sign of a malfunction.
If the power is disconnected during sewing:
Turn the main power to OFF and unplug the machine.
If you restart the machine, follow the instructions for operating the machine correctly.
227


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is 4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is 4000 in the language / languages: English as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is 4000

Brother Innov-is 4000 Quick start guide - English, German - 48 pages

Brother Innov-is 4000 User Manual - German - 246 pages

Brother Innov-is 4000 Quick start guide - Dutch - 48 pages

Brother Innov-is 4000 User Manual - Dutch - 247 pages

Brother Innov-is 4000 Quick start guide - French - 48 pages

Brother Innov-is 4000 User Manual - French - 246 pages

Brother Innov-is 4000 Quick start guide - Italian, Spanish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info