463623
226
Zoom out
Zoom in
Previous page
1/249
Next page
TROUBLESHOOTING
Appendix
215
8
Cannot lower the
presser foot with the
presser foot lever
Presser foot was raised using the “Presser Foot
Lifter” button.
Press the “Presser Foot Lifter” button to lower
the presser foot.
3
Thread tension is
incorrect
Upper threading is incorrect. Check the steps for threading the machine
and rethread the machine.
25
Bobbin is set incorrectly. Reset the bobbin. 22
Using improper needle or thread for the
selected fabric.
Check the “Fabric/Thread/Needle
Combination” chart.
36
Presser foot holder is not attached correctly. Reattach the presser foot holder correctly. 33
Thread tension is set incorrectly. Adjust the thread tension. 43, 154
Character pattern
does not turn out
Wrong presser foot was used. Attach the correct presser foot. “STITCH SETTING
CHART”
Pattern adjustment settings were set incorrectly. Revise the pattern adjustment settings. 103
Did not use a stabilizer material on thin fabrics
or stretch fabrics.
Attach a stabilizer material. 102
Thread tension is set incorrectly. Adjust the thread tension. 43, 154
Embroidery pattern
does not sew out
correctly
Thread is twisted. Use scissors, etc., to cut the twisted thread
and remove it from the race, etc.
Fabric was not inserted into the frame correctly
(fabric was loose, etc.).
If the fabric is not stretched tight in the frame,
the pattern may turn out poorly or there may
be shrinkage of the pattern. Set the fabric into
the frame correctly.
140
Stabilizing material was not attached. Always use stabilizing material, especially
with stretch fabrics, lightweight fabrics, fabrics
with a coarse weave, or fabrics that often
cause pattern shrinkage. See your authorized
dealer for the proper stabilizer.
138
There was an object placed near the machine,
and the carriage or embroidery frame hit the
object during sewing.
If the frame bumps something during sewing,
the pattern will turn out poorly. Do not place
anything in the area where the frame may
bump it during sewing.
146
Fabric outside the frame edges interferes with
the sewing arm, so the embroidery unit cannot
move.
Reinsert the fabric in the embroidery frame so
that the excess fabric is away from the sewing
arm, and rotate the pattern 180 degrees.
140
Fabric is too heavy, so the embroidery unit
cannot move freely.
Place a large thick book or similar object
under the arm head to lightly lift the heavy
side and keep it level.
Fabric is hanging off the table. If the fabric is hanging off the table during
embroidery, the embroidery unit will not move
freely. Place the fabric so that it does not hang
off the table or hold the fabric to keep it from
dragging.
146
Fabric is snagged or caught on something. Stop the machine and place the fabric so that
it does not get caught or snagged.
Embroidery frame was removed during sewing
(for example, to reset the bobbin). The presser
foot was bumped or moved while removing or
attaching the embroidery frame, or the
embroidery unit was moved.
If the presser foot is bumped or the
embroidery unit is moved during sewing, the
pattern will not turn out. Be careful when
removing or reattaching the embroidery frame
during sewing.
150
Loops appear on the
surface of the fabric
when embroidering
The thread tension is incorrectly set. Adjust the thread tension. 154
The tension of the upper thread is incorrectly set
for the combination of the fabric, thread and
pattern being used.
Use the embroidery needle plate cover. 146
The combination of the bobbin case and bobbin
thread is incorrect.
Change the bobbin case or bobbin thread so
that the correct combination is used.
146
Problem Cause Solution Page
226


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Innov-is 4000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Innov-is 4000 in the language / languages: English as an attachment in your email.

The manual is 7,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Innov-is 4000

Brother Innov-is 4000 Quick start guide - English, German - 48 pages

Brother Innov-is 4000 User Manual - German - 246 pages

Brother Innov-is 4000 Quick start guide - Dutch - 48 pages

Brother Innov-is 4000 User Manual - Dutch - 247 pages

Brother Innov-is 4000 Quick start guide - French - 48 pages

Brother Innov-is 4000 User Manual - French - 246 pages

Brother Innov-is 4000 Quick start guide - Italian, Spanish - 48 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info