718772
183
Zoom out
Zoom in
Previous page
1/212
Next page
TROUBLESHOOTING
181
Appendix
7
k
Slightly lift up the needle plate, cut any tangled
threads, and then remove the needle plate.
Remove the fabric and threads from the needle plate.
l
Remove any threads in the race and around the feed
dogs.
m
Turn the handwheel to raise the feed dogs.
n
Align the two screw holes in the needle plate with the
two holes at the needle plate mounting base, and then
fit the needle plate onto the machine.
o
Lightly finger-tighten the screw on the right side of the
needle plate. Then, use the disc-shaped screwdriver to
firmly tighten the screw on the left side. Finally, firmly
tighten the screw on the right side.
p
Replace the bobbin case and the needle plate cover
following steps
h through j in “Cleaning the Race”.
q
Check the condition of the needle, and then install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
* Refer to “CHANGING THE NEEDLE” on page 48.
Checking Machine Operations
If the needle plate has been removed, check machine
operations to confirm that installation has been completed
correctly.
a
Turn on the machine.
b
Select .
c
Slowly turn the handwheel toward you
(counterclockwise), and look from all sides to check
that the needle falls at the center of the opening in the
needle plate.
If the needle contacts the needle plate, remove the
needle plate, and then install it again, starting with step
m in “Removing the Fabric From the Machine” on
page 180.
d
Select zigzag stitch . At this time, increase the
stitch length and width to their maximum settings.
e
Slowly turn the handwheel toward you
(counterclockwise) and check that the needle bar and
feed dogs operate correctly.
Turn the handwheel to check that the feed dogs move
smoothly and do not contact the edges of the slots in the
needle plate.
1 Correct position of feed dogs
2 Incorrect position of feed dogs
f
Turn off the machine, and then install the presser foot
holder, presser foot and bobbin.
Never use a scratched or damaged presser foot.
Otherwise, the needle may break, or machine
performance may suffer.
* Refer to “Setting the Bobbin” on page 40 and
“CHANGING THE PRESSER FOOT” on page 50.
g
Correctly thread the machine.
* For details on the machine, refer to “UPPER
THREADING” on page 42.
h
Perform trial sewing with normal fabric.
If the fabric cannot be removed, even after
completing these steps, contact your nearest
Brother authorized service center.
Since the needle may have been damaged when
the fabric was caught in the machine, we
recommend replacing it with a new one.
Do not yet install the presser foot and thread.
1 Opening in the needle
plate
2 Handwheel
If the needle or feed dogs contact the needle plate,
the machine may be malfunctioning; therefore,
contact your nearest Brother authorized service
center.
Incorrect sewing may be the result of incorrect
upper threading or sewing thin fabrics. If there are
poor results from the trial sewing, check the upper
threading or the type of fabric being used.
a
b
a
b
183


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother Brother Innov-is XJ1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother Brother Innov-is XJ1 in the language / languages: English as an attachment in your email.

The manual is 12,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Brother Brother Innov-is XJ1

Brother Brother Innov-is XJ1 User Manual - German - 212 pages

Brother Brother Innov-is XJ1 User Manual - Dutch - 212 pages

Brother Brother Innov-is XJ1 User Manual - French - 212 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info