644488
170
Zoom out
Zoom in
Previous page
1/186
Next page
9-6 BE-1204B-BC • BE-1206B-BC
Chapter 9 Error code list
Code Error Messages Error Measures
E-BD
Lower shaft flash
memory error
Lower shaft flash memory error
E-BE
Lower shaft version-up
error
Lower shaft version-up error
E-BB,
BF
ERROR BB, BF Lower shaft motor undefined error
E-C1 ERROR C1 Area over during embroidering
This is not displayed in this model.
E-C2 Wiper out error Wiper out error
If the wiper is tangled with a thread, remove it.
Press the
or turn on the F/B switch on the
head to either side.
E-C3 ERROR C3 Embroidering data buffer empty
Check the connection of the communication
cable of the panel. If the cable is connected
correctly , press the
or turn on the F/B
switch on the head to either side. If the cable is
disconnected , turn off the power and connect the
cable.
E-C4 Presser foot down error Presser foot down error
E-C5 ERROR C5
Measured voltage value could not
be received form the lower shaft
motor CPU.
E-C6 ERROR C6
Voltage value could not be
transferred to the lower shaft motor
CPU.
E-C7 ERROR C7 Lower shaft error
E-C8 ERROR C8 Hook motor origin point error
E-C9 Embroidering start error Embroidering start error
E-CA ERROR CA No sewing permisson
This is not usually displayed.
E-CB
Spindle rotation speed
error
Spindle rotation speed error
Press the
or turn on the F/B switch on the
head to either side to cancel the error and press
the
. If the same error occurs again, there
is a possibility that the spindle is overloaded.
E-CC ERROR CC
Shuttle thread entanglement
automatic reset
This is not usually displayed.
E-CD
Spindle rotation
command sending error
Speed command can not be
received.
Turn the power off and on once. If the same
error occurs again, the main PCB is faulty.
E-CE
Cylinder bed position
error
Cylinder bed position error
E-CF ERROR CF
Rated voltage value could not be
received from the lower shaft
motor CPU.
This is not usually displayed.
E-D0 Power PC board error Power PC board error
Turn the power off and on once. If the same
error occurs again, the power PCB is faulty.
E-D1 Cooling fan motor stop Cooling fan motor stop. This is not usually displayed.
E-D2
Power voltage upper
limit error
Power voltage upper limit error
E-D3
Power voltage lower
limit error
Power voltage lower limit error
(1) The voltage setting is improper. -> Set it
again.
(2) Press the
or turn on the F/B switch on
the head to either side. If the same error
occurs again, the power PCB or the power
supply is faulty.
E-D4
Thread trimming motor
overcurrent
Thread trimming motor overcurrent
Turn OFF the power. The possible causes for this
error are, troubles of the thread trimming motor,
troubles of the main PCB, and troubles of the
drive PCB.
170


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother BE-1206B-BC Stand-Alone type at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother BE-1206B-BC Stand-Alone type in the language / languages: English as an attachment in your email.

The manual is 3,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info