644490

Brother BE-1206B-BC PC control Manual

252
Zoom out
Zoom in
Previous page
1/262
Next page
12-4 BE-1204B-BC • BE-1204C-BC • BE-1206B-BC
Chapter 12 Troubleshooting
Electrical Section
Cautions
• Be sure to turn off the power of the machine and unplug the power cord before checking cable
connections.
• When you check connection of the cables as instructed in this manual, also check connection and
continuity between connectors.
• Carry out items described in the "Measures" section in order of appearance.
• Some checks and replacement works can be conducted only by repair people. In such cases,
contact your dealer.
Symptom Measures
The machine does not operate even
if the power is turned on.
• Is the power cord of the machine plugged in?
→ Plug in the power cord.
• Isn't the emergency stop switch locked?
→ Unlock the emergency stop switch.
• Is the connector at the side of the control box connected?
→ Connect it after checking the connector name.
• Is the connector in the control box connected?
→ Connect it after checking the types and colors of the connectors.
• Isn't the fuse on the side of the control box blown?
• Is the fuse on the PCB in the control box blown?
→ Replace the fuse with a new one. If the fuse is blown again,
something is faulty. Check to see if the wiring is correct. Replace
the control box with a new one.
An overtravel error occurs. • Is the frame within the cap frame area?
→ Move the frame within the cap frame area and turn on the power.
• Check to see if the signal of the X area sensor turns ON and OFF in
PORT test mode.
→ When the signal does not change, refer to the block diagram
showing the cable connections and check to see if connection from
the X area sensor to the main PCB is proper. Replace the X area
sensor with a new one.
The needle stop position error
occurs.
• Is the pulley manually turned and out of the stop angle?
→ Turn the pulley, adjust the needle at the stop position, and reset the
error.
• Check the signal of the stop position sensor in the encoder test mode.
→ Refer to the adjustment or cable connection block diagram and
check connection from the needle position detention sensor to the
main PCB. Replace the needle position detection sensor with a
new one.
… 252 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother BE-1206B-BC PC control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother BE-1206B-BC PC control in the language / languages: English as an attachment in your email.

The manual is 7,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info