644490

Brother BE-1206B-BC PC control Manual

250
Zoom out
Zoom in
Previous page
1/262
Next page
12-2 BE-1204B-BC • BE-1206B-BC
Chapter 12 Troubleshooting
Mechanical Section
Problem Check point
! Thread breakage • Is the machine properly threaded?
• Is thread tension too high?
• Is the rotary hook assembly clogged?
• Is there thread in the bobbin?
• Is the needle bent?
• Is there a rough edge or flaw on the needle plate, rotary hook, or
bobbin case that might cut the thread?
• Is the needle installed correctly (direction, angle, etc.)
• Is the presser foot in contact with the material?
• Are the thread thickness and needle size correct?
• Is a thread with right-hand twist being used? (If such a thread is
used, replace with a thread with left-hand twist.)
• Is there any adhesive on the needle?
• Is the material tension too weak?
• Is there too much play between the outer rotary hook and inner
rotary hook?
• Does the outer rotary hook turn smoothly?
• Is the clearance between the rotary hook stopper and the rotary
hook adjusted correctly?
• Does the thread come out from the bobbin case smoothly?
! Needle (presser foot) interference
with embroidery hoop
• Is the embroidery hoop too small?
• Check the size and needle start position in the sewing data.
! Needle breakage • Is the needle attached correctly (direction, height, etc.)?
• Is the needle bent?
• Is the rotary hook attached correctly?
• Is the timing set correctly?
• Is there any backlash with the needle bar case (back/forth and
right/left)?
• Is the rotary hook stopper correctly attached to stop the rotary
hook?
• Is the needle size correct and the tip sharp?
• Does the thread pass through the hole center of the presser
foot?
! Not embroidered properly • Is the material edge caught in the machine?
(Are embroidery hoop and other related parts operating
correctly?)
• Is the material stretched properly?
• Is thread tension proper?
Does the lower thread come out smoothly?
Check these points once again
! Machine operation abnormal • Is embroidery data normal?
• Is the XY carriage belt loosened?
• Is the XY carriage belt damaged?
• Are any set screws for the XY drive pulley loosened?
• Are any fixing screws for the coupling of the Y drive shaft
loosened?
… 250 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother BE-1206B-BC PC control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother BE-1206B-BC PC control in the language / languages: English as an attachment in your email.

The manual is 7,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info