644489

Brother BE-1204B-BC - PC control Manual

254
Zoom out
Zoom in
Previous page
1/262
Next page
12-6 BE-1204B-BC • BE-1206B-BC
Chapter 12 Troubleshooting
Symptom Measures
ERROR A8 frequently occurs. • In the encoder signal test mode, manually turn the main shaft pulley
and check to see that the stop position signal is correct.
→ If the signal does not change, refer to the cable connection block
diagram and check to see if connection from the stop position
sensor to the power supply PCB is proper.
Thread trimming motor home position
error occurs.
• Is lint clogged between the travelling blades?
→ Remove it.
• Is the thread trimming motor operating?
→ If so, refer to the block diagram showing the cable connections and
check to see if connection from the thread breakage sensor to the
main PCB is proper. Also adjust the thread breakage sensor PCB.
(Refer to "Replacing thread breakage sensor PCB.)
• If it is not operating, refer to the block diagram showing the cable
connections and check to see if connection from the thread trimming
motor to the main PCB is proper.
• Check to see if connection from connector P3 of the main PCB to
connector P9 of the power supply PCB in the control box is proper.
• Check fuse F6 on the power supply PCB in the control box.
→ If it is blown, replace it with a new one. If it is blown again, replace
the power supply PCB.
Power frequency error occurs. • Check whether the connector P2 of the power supply PCB is fallen out.
Wiper out error occurs. • Does the wiper on the error head remain projected?
→ If the wiper is tangled with a thread, remove it. If the wiper does
not return smoothly, adjust it.
• Enter the solenoid test mode and operate the wiper motor. Check the
icon on the panel.
→ If the icon is not reversed white, check to see if connection from the
wiper sensor to the head PCB is proper. Replace the wiper sensor
with a new one. Replace the head PCB with a new one.
Embroidering data buffer empty,
embroidering start error occurs.
NOTE
This error may rarely occur according
to your PC's performance.If it occurs,
check the items shown on the left.
• Has the IF cable come off?
• Has the RS cable on the PC come off?
• Is the PC or machine controller down?
→ Reboot the PC or machine controller.
• Are any other software programs running on the PC?
• Replace the IF cable.
Main shaft rotation speed error
occurs.
• Enter the encoder signal test mode and manually turn the main shaft
pulley.
→ If it is abnormally heavy, the main shaft mechanism is faulty.
• Refer to the block diagram showing the cable connections and check
to see if connection from the main shaft motor to the drive PCB is
proper.
Cooling fan motor stops.
Exhaust fan motor stops.
When all three fans in the control box
stop
• Refer to the block diagram showing the cable connections and check
to see if connection from connector P4 of the power PCB in the control
box to connector P3 and P4 of the drive PCB .
• Check fuse in the fuse holder at the side of the control box.
→ If it is blown, replace it with a new one.
… 254 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother BE-1204B-BC - PC control at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother BE-1204B-BC - PC control in the language / languages: English as an attachment in your email.

The manual is 7,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info