525939

Brother 1134DW Manual

17
Zoom out
Zoom in
Previous page
1/68
Next page
10
TABLE OF
CONTENTS
Chapter
1
Chapter
2
Chapter
3
Chapter
4
Chapter
5
Chapter
6
Chapter
7
Chapter
8
Chapter
9
Chapter
10
Chapter
11
Chapter
12
Chapter
13
Chapter
14
Chapter
15
Chapter
16
Chapter
17
Chapter
18
Largo de puntada
Para cambiar el largo de las puntada:
(1)Busque el disco de ajuste del largo de las punta-
das en al lado izquierdo de la máquina.
(2)Gire el disco de ajuste del largo de las puntadas
hacia adelante para alargar la puntada a un
máximo de 4 mm.
Gire el disco de ajuste del largo de las puntadas
hacia atrás para acortar la longitud de puntada a
un mínimo de 2 mm.
* Un ajuste normal para el largo de las puntadas se
sitúa entre 2,5 y 3 mm.
Stitch Length
To change the stitch length,
(1)Locate the stitch length adjustment dial on the left
side of the machine.
(2)Turn the stitch length adjustment dial forward to
lengthen the stitch to a maximum of 4 mm (5/32
inch).
Turn the stitch length adjustment dial backwards
to shorten the stitch length to a minimum of 2 mm
(1/8 inch).
(3)The normal stitch length setting is 2.5 mm to 3
mm.
B
Stitch Width
Two-needle models
To change the stitch width.
(1)Move the stitch width lever (located on the left side
of the machine toward the front) up to reduce the
stitch width or down to increase the width.
The stitch width can be set between R4.5 mm (11/
64 inch) and 7 mm (9/32 inch).
The normal stitch width setting for regular overlock
stitch is 5mm (13/64 inch).
One-needle models
• The width is factory set to 3.5mm (9/64 inch).
A Two-needle models
B One-needle models
1 Stitch width lever
2 Regular needle plate
Ancho de puntada
Modelos de dos agujas.
•
Para cambiar el ancho de puntada.
(1) Mueva la palanca de anchura de las puntadas
(situada a la izquierda de la máquina, hacia
adelante) hacia arriba para reducir el ancho de
puntada, o hacia abajo para aumentar el ancho
de puntada.
Puede ajustar el ancho de puntada entre R4,5
mm y 7 mm.
El ajuste normal del ancho de puntada para una
puntada overlock corriente es de 5 mm.
Modelos de una aguja.
•
El ancho de las puntadas está establecido en la
fábrica en 3,5 mm.
A
Modelos de dos agujas
B
Modelos de una aguja
1
Palanca de anchura de las puntadas
2
Place de aguja normal
A
2
R
4
3
R
3.5
2
1
R
7
6
5
2
1
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brother 1134DW at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brother 1134DW in the language / languages: English, Spanish as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info