536074
31
Zoom out
Zoom in
Previous page
1/33
Next page
IMPORTANTThe child seat can be used with either a lap or a lap and
diagonal seat belt.
The larger the child the more upright the seat must be. To change the position
(if required) slide the support leg out until it engages in the desired position.
To slide the support leg in push the two support leg adjuster buttons and pull
up the support leg (dia 3a). Make sure the support leg is engaged rmly.
Place the child seat rearward facing with the back of the child seat positioned
centrally between the driver and passenger seat.
Extend the footprop fully by pressing the two release Buttons.Make sure
that the footprop tether brackets are facing forwards and that the straps
are not twisted. Lower the footprop and adjust the height so that it is within
approximately 30mm of the oor (dia 3b). Use the ruler printed on the back
page of this manual to get the correct distance from the footprop to the oor.
Loop a tether strap around both the
front driver and passenger seat as
shown (dia 3c).
If your car is equipped with a runner
loop on the seat runners, these may be
used as an alternative (see detail 3d).
IMPORTANTDo not install the tether
straps using the Luggage loops
3b
3c
3. Installing your child seat (rearward facing) in rear middle seat
3a
3d
Slide the loop ends of the tether straps between the front car seat and back
as shown (dia 2d &
dia 2e). Bring the hook ends of the tether straps
round the outside of the car seat and feed through the loops
2
. Snap
the hooks of the tether straps onto the xing rings on the back of the child
seat
3
. Provisionally tighten the tether straps by pulling the loose ends
downwards
4
.
Open the other lock-off arm , feed the seat belt under the lock-off arm and
attach the tongue into the buckle (dia 3g).
3h
Pull all of the seat belt slack through
the child seat ensuring the seat belt
is not twisted (dia 3h). When the belt
is as tight as possible, close the lock-
off arms on BOTH sides of the seat
ensuring that they click into place.
If the buckle now lies in the position
marked as wrong with a
and the
seat belt cannot be correctly tightened
(dia 3i), try another seating position in
the car.
3i
3g
3f
Pull off sufcient lap and diagonal belt (approx.600 – 900mm). Open the lock-
off arm on the side opposite the seat belt buckle. Pull back the child seat cover
to reveal the crotch strap. Feed the belt through the lock-off belt guide and seat
shell slot (dia 3f) on to the top face of the seat base, behind the crotch strap
(inset) and down through the slot on the other side of the child seat.
Finally tighten the tether straps by pulling the loose ends downwards (dia 3j)
until the footprop touches the oor. The footprop must rest on a solid oor –
not on lids of storage boxes or similar.
Once rmly strapped in, test the child seat by trying to move it back and forth
and side to side. If it seems loose, you must reinstall until rmly installed.
DO NOT rest the back of the child seat against the driver or front passenger
seats.
3j
9-25 kg
3e
2
4
3
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Britax-Romer MAX-WAY at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Britax-Romer MAX-WAY in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 15,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Britax-Romer MAX-WAY

Britax-Romer MAX-WAY User Manual - Dutch, French, Italian, Portuguese, Spanish - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info