Manual Brita On Line Active Plus (page 7 of 92) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

504590

Zoom out

Zoom in

1/92

ENGLISH 7

Please note that you will need the right drilling equipment

for your particular work surface or base. Make sure the

area under the dispenser is stable, especially if your work

surface is not made from wood. Please check the drilling

requirements for the material, use the appropriate drill and/

or consult a specialist.

Drill a hole (with a 12-mm bit) into the work surface where you

wish to set up the BRITA water dispenser.

Next, install the BRITA water dispenser (see ﬁ g. 5).

Then put the base (2) over the hole and ﬁ x the BRITA water

dispenser (1) in place using the supplied counter plate (4), the

gasket (3), the locking ring (5) and the hexagon nut (6).

3.4 Step 4: Attaching the hoses

We recommend that you ﬁ rst arrange all parts you need

in front of you. Before installation, please ensure that you

have a 3/8" or 1/2" cold water supply so that you can connect

the On Line Active Plus Water Filter Kit in addition to your

existing kitchen tap. Recommended tools for installation: an

adjustable wrench and a screwdriver.

For wall mounting (optional), you need: two screws (e.g. 5 mm

thread diameter) and, if required, two wall plugs suitable for your

type of wall.

Please follow the diagram on the next page (see ﬁ g. 6) and perform

the steps in the right order.

A a) Turn off the cold water supply

b) Please make sure your existing kitchen tap is pressureless by

opening the lever

No water should run through the existing kitchen tap!

c) Install supplied T-piece

NOTE

If you do have an additional free 3/8" cold water supply for

the BRITA On Line Active Plus kit in your kitchen, you do not

need to install the supplied t-piece!

d) Remove your existing 3/8" female kitchen tap hose from your

3/8" male cold water supply.

e) Connect t-piece with cold water supply.

a. Insert one 3/8“ gasket into the female nut of the supplied

t-piece.

b. Connect this end of the t-piece to your cold water supply.

f) Connect t-piece with kitchen tap

a. Only for kitchen tap with ﬂ exible hoses:

Connect your kitchen tap hose to one of the two 3/8" male

t-piece connections. Please, ensure proper sealing with the

already existing gasket from your existing kitchen tap hose.

This gasket is already integrated in the hose or a separate

part depending on your kind of kitchen tap hose.

b. Only for kitchen tap with squeeze connections (for kitchen

taps with tubes)

Connect your kitchen tap tube to one of the two 3/8” male

t-piece connections. Please, use the existing squeeze con-

nection nut with sealing components (as used before) and

the tube for the connection of your 3/8” kitchen tap to the

3/8 male t-piece connection.

B a) Put the hose (1) in place

b) Insert the medium-sized (3/8") gaskets into the respective

female threads of the two hose ends.

c) Now connect one end of the hose (1) to the ﬁ lter head inlet.

This is labelled “IN” (inlet) and marked with an arrow. Make

sure the gasket is seated correctly!

d) Now connect the other end of the hose (1) to your free cold

water supply/installed t-piece and ensure that the gasket is

correctly positioned!

NOTE

If your cold water supply does not ﬁ t the 3/8" connector on

the hose (1), use the supplied adapter if required. Your On

Line Active Plus Kit comes with a 1/2" adapter. Please go to

your nearest supplier for adapters in other sizes.

C a) Put the hose (2) in place.

b) Connect the small end, with the gasket that has already been

inserted into the hose (2), to the BRITA water dispenser

already installed (see Step 3.3).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Brita On Line Active Plus in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 6,7 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Brita On Line Active Plus Manual

Product: