504590

Brita On Line Active Plus Manual

5
Zoom out
Zoom in
Previous page
1/92
Next page
ENGLISH 5
3 On Line Active Plus Kit – easy installation
Before starting, please check that you have all the components
listed above (see fi g. 1) as well as the recommended tools.
There are 7 steps to the installation.
!
Prior to installation, read the Technical Data (chapter 7) and
the Important Information (chapter 9). After storage and
transport below 0°C, the product must be stored in the open
original packaging for at least 24 hours at the stated ambient
temperatures (chapter 7) for operation.
3.1 Step 1: Selecting the carbonate hardness
setting (++/+) on the fi lter head
The fi lter head has been set to meet most UK water conditions.
In some soft water areas though, you may wish to adjust the fi lter
head to your local settings. To do so, fi rst carry out a carbonate test
using the supplied testing strip. The strip can be found in the outer
wrapping of these Usage Instructions.
Using the testing strip:
• Let the red response fi eld of the probe soak in a glass of your
tap water for 1 second.
• After 1 minute, compare the colour of the response fi eld with
the table and read the appropriate setting from the table.
Depending on the colour of the testing strip, we recommend
setting your fi lter head as follows:
Setting + ++
(fi g. 2)
(fi g. 3)
Colour
Red, orange,
yellow
Green, dark
green
Capacity 1000 L 500 L
German Carbonate
Hardness [°dH]
up to 8.5 above 8.5
English Carbonate
Hardness [°eH]
up to 10.6 above 10.6
French Carbonate
Hardness [°fH]
up to 15.2 above 15.2
Grains per Gallon CaCO3
[gpg CaCO3]
up to 8.9 above 8.9
Milligram per Litre CaCO3
[mg/L CaO3]
up to 151 above 151
The fi lter head is set to “++” by default. To change the setting,
use an Allen key (5 mm). Turn in the direction of the arrow until
the “+” appears in the window.
The fi lter head contains a fl ow regulator already installed which
guarantees smooth water fl ow from your dispenser even at higher
water pressures.
3.2 Step 2: Starting the BRITA electronic
cartridge exchange indicator
A Beginning:
The BRITA electronic cartridge exchange indicator comes with "++"
setting and is already installed in your BRITA water dispenser.
– To start, pull off the strip in the direction of the arrow.
– The BRITA electronic cartridge exchange indicator's LED will
blink once red and once blue. If the BRITA water dispenser's
lever is turned to the open position, the LED will start blinking
blue continuously.
B Inserting the BRITA electronic cartridge exchange
indicator for the “+” setting
If you have changed your fi lter head to the “+” setting, please
consider that the electronic cartridge exchange indicator also has to
be changed.
a Take out the BRITA electronic cartridge exchange indicator (seen
as black rubber piece) from the bottom of the lever of the BRITA
water dispenser.
b Take the battery out carefully from the "++" indicator and put it
into the other cartridge exchange indicator in the separate bag,
marked with a “+”.
c The “+”-side of the battery has to be on top. As soon as the
battery has full contact a red and a blue light, on the back of the
BRITA electronic cartridge exchange indicator will blink once.
This shows that the BRITA electronic cartridge exchange indica-
tor has been set.
d Put the “+” BRITA electronic cartridge exchange indicator into
the faucet. The side with the battery has to face the BRITA logo
on the lever. Now the LED will blink blue when you turn the
BRITA water dispenser's lever to the open position
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brita On Line Active Plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brita On Line Active Plus in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 6,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info