504588
12
Zoom out
Zoom in
Previous page
1/54
Next page
10
4.2 Programming the Appliance
PROG RESET PROG RESET PROG RESET
“BATT” fl ashes when the
battery has run out
“PRG” fl ashes when the
programming mode is
activated
1,2,3,4,5” fl ashes during
“Memory Call-Up” and
represents the memory
level that is being called up
4.2.1 Programming the Litre Information
Briefl y press the “PROG” button
7
, the display changes to the programming mode,
“PRG” fl ashes in the display
8
. (How to identify the fi lter capacity is described in the
lter system manual.)
Note: Press the “PROG” button
7
again to leave programming without making any
changes.
Press the “RESET” button
9
to jump to the litre information. The relevant number
ashes in the display
8
.
Press the “RESET” button
9
until the desired number is shown fl ashing in the
display
8
.
Press the “PROG” button
7
to reach the next digit to be entered. The relevant digit
ashes.
Repeat the steps above until the litre information determined has been entered.
Press the “PROG” button
7
to con rm the litre information entered and to leave the
programming mode. The “PRG” fi eld in the display
8
no longer fl ashes.
The litre information entered is shown in the display
8
, the system can now be com-
missioned.
4.3 Installation of the Sensor
Note: During installation, pay attention to the direction of fl ow.
Close the water inlet.
If a fi lter system is already installed, remove the outlet hose
4
by loosening the union
nut.
Tighten the union nut
5
of the sensor
1
on the fi lter head. If necessary, insert a fl at
seal
6
.
Tighten the outlet hose
4
on the sensor
2
.
!
Caution: The max. tightening torque at the 3/8" connections must not exceed
15 Nm!
4.4 Installation of the Display Unit
The display unit can be attached to the desired position with double-sided adhesive tape
or a screw (neither included in the delivery scope).
!
Caution: There must not be any water pipes or electrical
cables behind the mounting surface. Do not lay the connecting cable parallel to cables
conducting electricity because this can lead to an impairment of the sensor signal.
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brita FlowMeter 10-100A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brita FlowMeter 10-100A in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info