753040
46
Zoom out
Zoom in
Previous page
1/64
Next page
Evap 12
¹ See chapter 10 for version adjustment
Section 10 Version adjustment
The following components and table apply up to serial number BR2018-H-00025:
• Length of drain hose 500mm
• Drain hose Ø = 15mm
• Knee on drain instead of wire spring clamp
• Alarm and alarm table:
Alarm LED
Meaning
Action
Alarm LED flashes
No airflow
Check that the HRV unit fan is moving air.
Alarm LED
continuously on
Contact with SHC80
sensor broken
Check SHC80 wiring and if necessary repair, check that
the light on SCH80 sensor flashes regularly, if not
replace faulty sensor.
Alarm LED
continuously on
No water supply
- Check if the water tap is open.
If the tap is open and there is a demand (outside
temperature below 12 ° C) check the strainer in the
connection coupling, it must be clean.
- Check the functioning of the water valve. Disconnect
the black supply hose from the knee on the unit, and
reset the unit by plugging out and plugging in again; if
water comes out and the water valve and this stops after
90sec, then the valve is OK, the water keeps flowing or
no water comes out of the hose, then the water valve is
defective, replace the water valve. If the water valve
works and the matrix does not get wet after the valve has
switched, the legionella filter is clogged; replace the
cassette.
If the matrix does get wet and still has an alarm, the
matrix is contaminated and the cassette must be
replaced. Product No .: 351025
Alarm LED
continuously on
Heating faulty
Check air temperature after the humidifier, this must be
>17ºC, if not air heater is faulty. Call installer for
replacement.
Alarm LED
continuously on
T3 sensor outside air
faulty
Check wiring for break or wear, in case of doubt replace.
Testing can be done by keeping the sensor at 8°C or
colder in water or air; the Evap must then be activated
because the water valve opens.
Service LED
continuously on
The cassette must be
replaced
To be able to humidify safely it is necessary to replace
the complete cassette; Order product code 351025 from
your dealer.
In the interim, you can
reset the service alarm at
the bottom by pressing and
holding the reset button
for 30 seconds. The
opening is located next to
the service LED.
ATTENTION the LegioSafe filter will soon become
obstructed, after which proper and safe operation is no
longer guaranteed!!
Power LED flashes
There is no
communication between
optional controller and
humidifier
Check status of the batteries on controller. If necessary
replace (4xAAA).
Reduce distance between the Evap module and the
controller if WIFI symbol is not visible, press (MODE)
button to restore and test connection.
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Brink Evap at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Brink Evap in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info