729964

Bresser 7060100 MyTime Crystal P Colour Manual

9
Zoom out
Zoom in
Previous page
1/16
Next page
9 / 16
4. Wait until the indoor temperature is displayed on the base station.
NOTICE!For permanent operation, mains power supply is recommended. Alternatively a
power supply with batteries is also possible. Proceed as follows:
5. Remove the battery compartment cover.
6. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.
7. Replace the battery compartment cover.
8. Wait until the indoor temperature is displayed on the base station.
NOTICE!When switching from mains power supply to battery power supply or vice versa,
the power supply is being disabled for a short moment for technical reasons. In this process
all settings made previously, will be deleted.
Remote sensor
1. Loosen the screws at the battery compartment cover with a small Philips screwdriver and remove
the cover.
NOTICE!Make sure not to lose the thin silicone sealing frame when removing the battery
compartment cover. It is an important protection against water infiltration and often ad-
heres at the battery compartment cover.
2. Insert the batteries into the battery compartment. Ensure that the battery polarity (+/-) is correct.
3. Set the channel selector switch to the desired channel (1, 2 or 3).
NOTICE!This weather station can be operated with up to 3 remote sensors. Each remote
sensor being connected must be operated on a different channel. If only one remote sensor
is connected, it should be operated on channel 1. Always press TX button after changing the
channel.
4. Press RESET button. The function indicator lights up for a short moment.
5. Put the sealing frame back onto the edge of the battery compartment.
6. Replace the cover and retighten it with the screws.
10 Manual time setting
1. Press and hold SET button for approx. 2 seconds to change to time setting mode.
2. Digits to be set are flashing.
3. Press UP or DOWN button to change the value.
4. Press SET button to confirm and continue to the next setting.
5. Settings order: Hours > Minutes > Change day/month display > Language > Year > Month >
12/24-hours mode
6. Finally press the SET button to save the settings and exit the setting mode.
11 Alarm setting
1. Press MODE button to switch to alarm time display.
2. Press and hold ALARM button for approx. 2 seconds to enter the alarm time setting mode (AL).
3. Digits to be set are flashing.
4. Press UP or DOWN button to change the value.
5. Press ALARM button to confirm and continue to the next setting.
6. Settings order: Hours > Minutes
7. Finally press the ALARM button to save the settings and exit the setting mode. Alarm will be activ-
ated automatically. The symbol will be displayed.
8. Press MODE button in normal display mode to display the alarm time.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 7060100 MyTime Crystal P Colour at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 7060100 MyTime Crystal P Colour in the language / languages: English as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bresser 7060100 MyTime Crystal P Colour

Bresser 7060100 MyTime Crystal P Colour User Manual - German - 16 pages

Bresser 7060100 MyTime Crystal P Colour User Manual - French - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info