632904

Bresser 70-20000 Connect Set Manual

17
Zoom out
Zoom in
Previous page
1/72
Next page
17
Note: Please refer to “Router compatibility” and “Troubleshooting” sections if you encounter any problem when setting up
the gateway.
Wind meter (Fig. 3, 2)
• 1. Registration and setup
1) Align and connect the wind speed cups and wind vane to the wind meter and tighten the screws.
2) Place the wind meter next to the gateway.
3) Enable your WiFi reception on your iOS / Android device and run the “ BRESSER Connect” app .
4) Select “Weather” and then tap the “ i ” on the upper right corner to enter the setting display.
5) Tap “Wind, Temperature, Humidity”.
6) Tap ”+” on the upper right to add a new wind meter.
7) Open the battery door of the wind meter.
8) Use the compass on the wind meter and turn the wind vane so it is pointing due north (Fig. 4).
9) Hold the wind vane pointing due north and do not allow it to turn. Insert 2 pieces of AA batteries according to the
polarity indicated. The red LED indicator above the battery cover of the wind meter will flash few times right after battery
installation. Be sure the vane is pointing due north at the moment when red LED flashes and the calibration is now
completed.
10) If the wind vane is not pointing due north when the red LED first flashes, remove batteries and repeat step 8 and 9.
11) Tap “Connect” on the app within 30 seconds of battery installation to search for the wind meter.
12) Once connected, “Sensor is connected” appears and you have successfully registered your wind meter. You may
proceed to change the name and photo. Tap the “Save” icon on the upper right corner anytime to save and exit.
Replace the battery cover and tighten the screws on the wind meter
13) Return to the “Weather” main display and the wind speed/ direction, temperature and humidity readings will appear
within a short period.
• 2. Testing the effective transmission range
It is recommended to perform a simple transmission test before mounting the wind meter so as to ensure it is within the ef-
fective transmission range.
1) Select a mounting location for the wind meter that is:
- outdoors, not blocked on top or sides, so wind can freely reach the wind meter
- within 100 meter (328 feet) open area from the gateway. The distance is reduced when obstacles are between
the wind meter and the gateway
- Place the wind meter 1 meter above ground to simulate the minimum height after mounting
2) If there is wind when testing, let the wind meter run freely and follow the steps below:
- Run the app and go to the “Weather” page (make sure your WiFi is enabled on your iOS / Android device and
you are within the WiFi coverage area)
- If wind speed/direction readings continue to change and update every few minutes, your wind meter is within the
effective transmission range. Go to below section for mounting your wind meter.
3) If there is no wind when testing, wait for 25 minutes and follow below steps:
- Run the app and goes to the “Weather” page (make sure your WiFi is enabled on your iOS / Android device and
you are within the WiFi coverage area)
- If wind speed/direction reading still appears on the screen, your wind meter is within the effective transmission
range. Go to below section for mounting your wind meter
- If “---“ appears on the wind speed/direction page or “sensor is not connected” appears on its setting page, the
wind meter is out of the range.
Shorten the distance between the wind meter and the gateway. Go to the wind meter setting page and tap [Connect]
again to reconnect the sensor. Repeat this procedure until the sensor is connected.
Note: If you have run the Connect system for a long period of time, and one day your wind meter fails to connect with the
system while the rest of the sensors work fine, it’s likely that the battery level in the wind meter is low. Please reinstall new
batteries and follow the setup procedure in the manual to reconnect with your Connect system.
DE
GB
FR
NL
IT
ES
Garantie
Warranty
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bresser 70-20000 Connect Set at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bresser 70-20000 Connect Set in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info