Manual Boston Boston M 250 (page 7 of 14) (English)

582033

Zoom out

Zoom in

1/14

If you are using spade lugs, attach them to the wires as speciﬁed by the manufacturer. Loosen the top cap by turning it

counter-clockwise until there is enough clearance for the spade lug to be positioned around the terminal post. Place the

spade lug around the post and turn the top cap clockwise by hand to clamp it in place. Do not use tools to tighten it.

Repeat for the other loudspeaker connections.

If you are using single or dual banana plugs, attach them to the wire as speciﬁed by the manufacturer. Turn the top cap

of the terminal clockwise to ensure that it is fully seated. Do not use tools to tighten it. Insert the banana plug into the

hole provided in the center of the top cap. Repeat for the other loudspeaker connections.

For information on connecting the speaker wires to your receiver or ampliﬁer, refer to its owner’s manual.

Important!

To ensure the best performance, observe polarities when making loudspeaker connections. The terminal cups have +

and – symbols included on them and the top caps have a red ring for + and black ring for –. Connect each + terminal

on the back of the ampliﬁer or receiver to the respective + (red) terminal on each loudspeaker. Connect the – (black)

terminals in the same way. If the connections are not made correctly, it can cause poor bass response and imaging. Also,

to avoid short circuits that may damage your equipment, be careful not to let the ends of the wires to make contact with

the ends of any other wires.

Subwoofer

For optimal results, place the subwoofer on the same wall (or in a corner) as your front speakers. In principal, the lower

the crossover point, the greater the distance the subwoofer can be from the front speakers, however, the sound is typi-

cally best when the subwoofer is within 12 feet (3.5m) of the front speakers. The perceived level of bass output from the

subwoofer will vary signiﬁcantly at diﬀerent positions in the room. When placed near walls, the output level is empha-

sized with corner placement providing the highest perceived output level. Placement away from walls may produce too

little perceived bass.

Regardless of the perceived bass level within the room, you always have the ability to adjust the level

of the subwoofer from the built in volume control or from the level control of your preampliﬁer or receiver. If at any time

you move the subwoofer, be sure to re-check your outputs levels and EQ settings if any. Since the human ear is less able to

localize low frequencies, the bass will still appear to come from the front speakers. Experimentation is key but most

positions in the room should work well

IMPORTANT: Do not place the subwoofer where there is a chance of contact between the rear panel and drapes

or furniture. The ampliﬁer panel also serves to dissipate heat and should have at least 3 inches (76mm) clearance so it

does not overheat.

NOTE: Power is always supplied to the MSubwoofer electronics unless it is unplugged or switched to the OFF position

using the power switch located on the rear panel. The auto-on circuitry only activates or deactivates the power ampliﬁer.

Make sure your MSubwoofer and preamp/receiver are unplugged when making connections.

Power: When plugging in your MSubwoofer be sure to use a wall outlet, or dedicated electrical outlet. Some receivers

will provide a switched outlet. Do not use this. These on board electrical outlets do not oﬀer the amount of current or

proper isolation required by a power ampliﬁer, such as the one in your MSubwoofer.

Line level or LFE:

On most systems use the Line Level input or the LFE input. These inputs accept the line-level signal

from your preamp/receiver’s subwoofer output. Your receiver’s manual should indicate which input is most appropriate.

Downloaded from www.Manualslib.com manuals search engine

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Boston Boston M 250 in the language / languages: English as an attachment in your email.

The manual is 1,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Boston Boston M 250

Boston Boston M 250 User Manual - English, German, French, Italian, Swedish, Spanish - 72 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Boston Boston M 250 Manual

Product: