721847

Bostitch IC50-1-E Manual

7
Zoom out
Zoom in
Previous page
1/56
Next page
7
GB
ADJUSTING THE MAGAZINE
(IC60-1-E & IC70-1-E ONLY)
1. Release the canister latch on the rear of the canister.
(Fig. 8)
2. Pull out the canister bottom by swinging right to left
until tabs disengage. (Fig. 9)
3. Inside the canister bracket there are settings in
inches and millimeters. The canister is adjusted
correctly when the length of fastener being used
isshown in the window of the canister bottom.
4. Push back the canister bottom and engage the latch
ADJUSTING THE MAGAZINE
(IC50-2-E, IC50-1-E, IC90-1-E, IC90P-1-E,
IC90C-1-E ONLY)
1. The magazine contains an adjustable nail platform
on which the nail coil rests. The nail platform can
beadjusted up and down to three nail settings.
2. To change settings, pull up on the post and twist
tothe correct step. (Fig. 10)
Model
Step Number / Nail Length (mm)
1 2 3 4
IC50-2-E 25-27 32 38-45 50
IC50-1-E 25-27 32 38-45 50
IC90-1-E 80-90 70-75 50-65
-
IC90P-1-E 80-90 70-75 50-65
-
IC90C-1-E 80-90 70-75 50-65
-
GUIDE ROD (IC50-2-E & IC50-1-E ONLY)
The tool includes a guide rod that needs to be adjusted
depending on the type of nails:
- The rod should be in the depressed position for
standard plastic inserted nails with 7mm pitch (Fig. 11)
- The rod should be in the released position for wire
welded nails and plastic inserted nails with 6mm pitch
(Fig. 12)
TRIP OPERATION MODE
THESE TOOLS ARE FITTED WITH 2 DIFFFERENT
ACTUATION MODES DEPENDING ON THE MODEL.
m WARNING! Always disconnect air supply before
making adjustments as accidental actuation may
occur, possibly causing injury.
SEQUENTIAL ACTUATION MODE:
Models: IC50-2-E
CONTACT ACTUATION MODE:
Models: IC50-1-E, IC60-1-E, IC70-1-E, IC90-1-E,
IC90P-1-E, IC90C-1-E
IMPORTANT: The IC90C-1-E is fitted with an
auxiliary handle that includes an additional safety lever
(Fig. 13). This additional lever must be fully depressed
throughout the contact actuation sequence for the tool
to drive any fasteners. If the auxiliary handle lever is
not depressed, the tool will not cycle.
SEQUENTIAL ACTUATION
The sequential actuation requires the operator to
hold the tool against the work with the safety yoke
depressed before pulling the trigger. In order to drive
additional fasteners, the trigger must be released and
the tool lifted away from the work, before repeating the
above mentioned steps.
This makes accurate fastener placement easier,
for instance on framing, toe nailing and crating
applications. The sequential actuation allows exact
fastener location without the possibility of driving
a second fastener on recoil, as described under
Contact Trip (below). The sequential actuation tool
has a positive safety advantage because it will not
accidentally drive a fastener if the tool is contacted
against the work - or anything else - while the operator
is holding the trigger pulled.
© BOSTITCH 2019
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
compliance for the products.
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
rien que les produits soient conformes aux normes CE.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen
nicht die CE-Richtlinien für Produkte.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
zeggen dat de producten voldoen aan de CE-vereisten.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
produkterne.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
yhdenmukaisuutta.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα
αντίγραφα του παρόντος εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
conformità CE per i relativi prodotti.
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for
CE-merking for produktet.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu
nie stanowią deklaracji zgodności CE prezentowanych produktów.
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
výrobky.
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem
jelenti a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bostitch IC50-1-E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bostitch IC50-1-E in the language / languages: All languages as an attachment in your email.

The manual is 2,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info