777041

Bosch UniversalHedgeCut 18 50 Manual

15
Zoom out
Zoom in
Previous page
1/236
Next page
English | 15
Sawing Function
Although the tooth opening allows wood to be cut up to Ø
20mm can be cut with the 55 cm blade, the tip of the blade
is designed to cut wood up to Ø 25 mm.
Working with the Hedgecutter (see figure F)
Move the hedgecutter evenly forward along the cutting line.
The double edge cutting blade enables cutting in either dir-
ection, or with a side to side motion.
Cut the sides of the hedge first, then the top.
To cut the sides straightly, we recommend cutting from bot-
tom to top in the direction of growth. Younger stems tend to
move outwards when cutting them from top to bottom, res-
ulting in shallow patches or holes in the hedge.
To reach a level finish, fasten a piece of string along the
length of the hedge at the required height and use as an
alignment guide. Cut the hedge just above the string.
Pay attention that no objects such as wires are cut. The
blade or drive can be damaged.
Anti Blocking
If the blade stalls on a tough material, the load of the motor
increases. The intelligent micro-electronics senses this over-
load condition and repeatedly reverses the motor, in order
to prevent stalling and to cut the branch through.
This audible reversing cut action continues for up to 15
rounds if trigger is pressed.
After cutting through, the garden product continues in its
normal mode, or in case the overload condition continues
the blades automatically stop in the open position (e.g. in
case a piece of metal fence accidentally blocks the garden
product).
Troubleshooting
Hedgecutter
Problem Possible Cause Corrective Action
Hedgecutter does not
operate Battery discharged Recharge battery; also see “Battery Charging”
Battery not fully connected Ensure both locking levels are engaged
Hedgecutter operates
intermittently Internal wiring of garden tool defective Contact Service Agent
On/Off switch defective Contact Service Agent
Motor reverses repeatedly then stops after 3s. see “Working Advice” (Anti Blocking)
Motor runs but blades
remain stationary Internal Error Contact Service Agent
Cutting blade hot Cutting blade blunt Have blade sharpened
Cutting blade has dents Have blade inspected/overhauled
Too much friction, due to lack of lubricant Apply lubricant spray
Blade will not move Battery discharged Recharge battery; also see “Battery Charging”
Machine defective Contact Service Agent
Excessive vibrations/
noise Machine defective Contact Service Agent
Cutting time per bat-
tery charge too low Too much friction, due to lack of lubricant Apply lubricant spray
Blade needs cleaning Clean blade
Poor cutting technique see “Working Advice” (figureF)
Battery not fully charged Recharge battery; also see “Battery Charging”
The blades are running
slow or the anti block-
ing feature is not func-
tioning
Battery discharged Recharge battery; also see “Battery Charging”
Battery stored outside of battery temperature Allow battery to warm naturally to room temperat-
ure (within battery operating temperature 0–
35°C)
Bosch Power Tools F 016 L94 155 | (05.05.2021)
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch UniversalHedgeCut 18 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch UniversalHedgeCut 18 50 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian as an attachment in your email.

The manual is 4.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch UniversalHedgeCut 18 50

Bosch UniversalHedgeCut 18 50 Additional guide - English, German, Dutch, Danish, French, Italian, Polish, Swedish, Turkish, Spanish, Norwegian - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info