“Pulse steam” function
This appliance has a special function for tackling
difficult creases.
When the steam release button is activated, the steam
generator will give three powerful shots of steam so
that the steam reaches even deeper into the fabrics.
1. Set the temperature selector (14) on “• • •”
2. Press the steam release button (15) on the bottom
of the handle two times shortly (double-click)
or (model dependent)
Shortly press the steam release button (16) on the
top of the handle.
Remark : It is possible to stop the shots of steam by
pressing the steam button shortly again.
“Ultimate steam” function
(model dependent)
The “Ultimate steam” function helps to make a faster
softening of very stubborn garments like Jeans or linen
tablecloth. When activating the “Ultimate steam” button
(16) the steam generator produces an extra amount of
steam. The function should be used during intervals of a
few seconds, to be the most effective.
1. set the temperature selector (14) on “•••”
2. press the “Ultimate steam” button (16).
Important:
• The steam hose may get hot if you are ironing for
long periods.
•
Note: Some water drops may appear when you use
the “Pulse steam” or the “Ultimate steam” function
for the first time. The water drops will disappear after
you have used the function for some time.
Ironing without steam
1. Begin ironing but without pressing the steam release
button.
Vertical steam (C)
1. Set the temperature control to the “•••” or “max”
position.
2. You can steam iron curtains and hanging garments
(jackets, suits, coats...) by placing the iron in a
vertical position and pressing the steam release
button.
Never direct the steam jet at garments that are
being worn.
Never aim the steam at people or animals.
Energy saving “eco” button
(depending on the model)
If the “Energy saving” button (8) is switched on, the
energy consumption of the appliance will be reduced,
by means of automatic reduction of electricity and
water consumption. A good ironing result can be
obtained for most of the garments.
Use the normal energy setting only for thick and highly
wrinkled fabrics.
Note: If you work with the “Energy saving”
function, the variable steam regulation and
temperature regulation can still be used as
recommended.
Cleaning & Maintenance
Always unplug the appliance from the mains
supply before carrying out any cleaning or
maintenance operation on it.
1. After ironing, pull out the plug and allow the
appliance to cool down before cleaning.
2. Wipe the housing, handle and iron body with a
damp cloth.
3. If the soleplate is soiled with dirt or scale, clean it
with a damp cloth.
4. Never use abrasive products or solvents.
Storing the appliance (D)
1. Always allow the appliance to cool down before
storing it.
2. Set the main power to the “0” position and
disconnect the mains cable.
3. Place the iron on the iron pad, standing on the
soleplate.
4. Store the mains cable in the storage compartment
(5) and the steam hose in the storage fixing (3). Do
not wrap the cords too tight.
5. Use the carrying handles (4) on the sides when
moving the appliance.
Fabric protection soleplate cover (E)
(depending on the model)
The fabric-protection soleplate cover is used for steam-
ironing delicate garments at maximum temperature
without damaging them. Use of the soleplate cover
also does away with the need for a cloth to prevent
shine on dark materials.
It is advisable to first iron a small section on the inside
of the garment to see if it is suitable.
To attach the soleplate cover to the iron, place the tip
of the iron into the end of the soleplate cover and pull
the elastic strap over the lower rear of the iron until
it fits tightly. To release the soleplate cover, pull the
elastic strap and remove the iron.
The fabric-protection soleplate cover may be purchased
from the customer service or specialist shops:
Accessory code
(After-sales)
Name of accessory
(Specialist outlets)
571510 TDZ2045
en
