746083
25
Zoom out
Zoom in
Previous page
1/44
Next page
Cooking assist functions en
25
Connecting the wireless temperature sensor to the
control panel
You will need to connect the wireless temperature
sensor to the control panel before using the cooking
functions for the first time.
To connect the wireless temperature sensor to the
control panel, follow the instructions below:
1. Select the ™‚… menu; see the section on ~ "Basic
settings"
The hotplate indicator will light up.
2. Select the hotplate and its indicator will light up. A
signal will sound. The å indicator will light up.
3. Press the å symbol on the wireless temperature
sensor within 30 seconds.
After a few seconds, the status of the connection
between the temperature sensor and the control
panel will appear on the hotplate's display.
The cooking functions are made available once the
temperature sensor has been connected to the
control panel correctly.
If there is a fault with the temperature sensor, the
connection may not be established correctly for the
following reasons:
Bluetooth communication error.
You did not press the symbol on the temperature
sensor within 30 seconds of selecting a hotplate.
The battery in the temperature sensor has run
out.
Reset the wireless temperature sensor and follow
the connection procedure once again.
If the temperature sensor and the control panel are
not connected correctly due to a transmission error,
follow the connection procedure once again.
If the display continues to show incorrect connection
, contact our technical after-sales service.
Resetting the wireless temperature sensor
1. Touch and hold the å symbol for approximately 8-
10 seconds.
While you are doing this, the temperature sensor's
LED indicator will light up three times. When the LED
lights up for the third time, it will start to reset the
temperature sensor. At this point, you will need to lift
your finger off the symbol.
Once the LED goes out, this means that the wireless
temperature sensor has been reset.
2. Repeat the connection procedure from point 2.
Setting procedure
1. Attach the temperature sensor to the saucepan; see
the section on ~ "Preparing and maintaining the
wireless temperature sensor"
2. Place a saucepan filled with sufficient liquid on the
required hotplate and always put the lid on.
3. Select the hotplate on which you have placed the
saucepan with the temperature sensor.
4. Touch the å symbol on the temperature sensor.
The indicator å will light up in the control panel.
5. Select the right temperature setting from the table.
The function has now been activated.
The temperature symbol å will flash until the water
or oil has reached the right temperature for adding
the food. A signal will sound and the temperature
symbol will stop flashing.
6. Once the signal has sounded, take the lid off and
add the food. Keep the lid on during cooking.
Note: Do not cover the pan when using the "Frying
with a large amount of oil in the saucepan" function.
Switching off cooking functions
Select the hotplate and set it to . on the control
panel. The hotplate will switch off and the residual heat
indicator will appear.
Note: To re-activate the cooking functions, wait for
approximately 10 seconds.
Status
Connected correctly
Not connected correctly: Transmission error.
ƒ
Not connected correctly: Temperature sensor fault.
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PXY695DX6E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PXY695DX6E in the language / languages: English as an attachment in your email.

The manual is 3,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PXY695DX6E

Bosch PXY695DX6E User Manual - German - 48 pages

Bosch PXY695DX6E User Manual - Dutch, Italian - 88 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info