460538
23
Zoom out
Zoom in
Previous page
1/159
Next page
English | 23
Bosch Power Tools 2 609 004 236 | (5.5.10)
Technical file at:
Robert Bosch GmbH, PT/ESC,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
07.04.2010
Assembly
f Before any work on the machine itself (e. g.
maintenance, tool change, etc.) as well as
during transport and storage, remove the
battery from the power tool. There is danger
of injury when unintentionally actuating the
On/Off switch.
Battery Charging (see figure A)
f Use only the battery chargers listed on the
accessories page. Only these battery charg-
ers are matched to the lithium ion battery of
your power tool.
Note: The battery is supplied partially charged.
To ensure full capacity of the battery, complete-
ly charge the battery in the battery charger be-
fore using your power tool for the first time.
The lithium ion battery can be charged at any
time without reducing its service life. Interrupt-
ing the charging procedure does not damage the
battery.
The lithium ion battery is protected against
deep discharging by the “Electronic Cell Protec-
tion (ECP)”. When the battery is empty, the ma-
chine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
Do not continue to press the
On/Off switch after the ma-
chine has been automatically switched off. The
battery can be damaged.
To remove the battery 4, press the battery un-
locking button 5 and pull the battery upward out
of the power tool. Do not exert any force.
The battery is equipped with a NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C. A
long battery service life is achieved in this man-
ner.
Observe the notes for disposal.
Replacing/Inserting the Saw Blade
f When mounting the saw blade, wear protec-
tive gloves. Danger of injury when touching
the saw blade.
Selecting a Saw Blade
An overview of recommended saw blades can
be found at the end of these instructions. Use
only T-shank saw blades or saw blades with 1/4"
universal shank (U-shank). The saw blade
should not be longer than required for the in-
tended cut.
Use a thin saw blade for narrow curve cuts.
Inserting the Saw Blade (see figure B)
f Clean the shank of the saw blade before in-
serting it. An unclean shank cannot be fas-
tened securely.
If required, remove the dust cover 11 (see “Dust
Cover”).
Push the saw blade holder 17 upward in the di-
rection of the arrow. Insert the saw blade 14
(teeth in cutting direction) to the stop into the
saw blade holder.
While inserting the saw blade, pay attention that
the back of the saw blade is positioned in the
groove of the guide roller 12.
f Check the tight seating of the saw blade. A
loose saw blade can fall out and lead to inju-
ries.
Removing the Saw Blade (see figure C)
Push the saw blade holder 17 upward in the di-
rection of the arrow and remove the saw blade
14.
Dr. Egbert Schneider
Senior Vice President
Engineering
Dr. Eckerhard Strötgen
Head of Product
Certification
WARNING
OBJ_BUCH-1204-001.book Page 23 Wednesday, May 5, 2010 8:13 AM
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PST 18 LI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PST 18 LI in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info