473381
9
Zoom out
Zoom in
Previous page
1/60
Next page
English - 2
Before any work on the machine (e. g.
maintenance, tool change, etc.) as well as
when transporting and storing, always set
the rotational direction switch to the centre
position. Unintentional actuating of the On/
Off switch may result in personal injury.
Do not open the battery yourself. There is
danger of a short circuit.
Protect the battery against heat, e. g., in-
cluding against continuous sun irradiation
and fire. There is danger of explosion.
Do not short-circuit the battery. There is
danger of explosion.
Use appropriate detectors to determine if
utility lines are hidden in the work area or
call the local utility company for assist-
ance.
Contact with electric lines can lead to fire and
electric shock. Damaging a gas line can lead
to explosion. Penetrating a water line causes
property damage.
Hold the power tool only by the insulated
gripping surfaces when performing an op-
eration where the cutting tool may contact
hidden wiring. Contact with a “live” wire will
also make exposed metal parts of the power
tool “live” and shock the operator.
Hold the machine with a firm grip. High re-
action torque can briefly occur while driving in
and loosening screws.
The machine is intended for driving in and loos-
ening screws as well as for drilling in wood, metal,
ceramic and plastic.
Battery Charging
A battery that is new or has not been used for a
longer period does not develop its full capacity
until after approximately 5 charging/discharging
cycles.
To remove the battery 7, press the unlocking but-
tons 8 and pull out the battery downwards. Do not
exert any force.
The battery is equipped with an NTC temperature
control which allows charging only within a tem-
perature range of between 0 °C and 45 °C.
A long battery service life is achieved in this man-
ner.
A significantly reduced working period after
charging indicates that the batteries are used and
must be replaced.
Observe the notes on environmental protec-
tion.
Open the drill chuck 3 by turning until the tool can
be inserted. Insert the tool.
Firmly tighten the sleeve of the keyless chuck 3
by hand. This automatically locks the chuck.
Rotate the sleeve in the reverse direction to re-
move the tool.
Screwdriving (see figure )
Insert the screwdriver blade 6 directly into the
tool holder or when using screwdriver bits 10, ad-
ditionally use the universal bit holder 11.
Inserting the Battery
Use only original Bosch O-pack batteries with
the voltage given on the type plate of your ma-
chine.
Set the rotational direction switch 5 to the centre
position = lock-off and allow the charged bat-
tery 7 to engage into the handle.
Reversing the Rotational Direction
Operate the rotational direction
switch 5 only at a standstill.
The rotational direction
switch 5 is used to re-
verse the rotational direc-
tion of the machine. How-
ever, this is not possible
with the On/Off switch 4
pressed.
Right Rotation ( )
Turn the rotational direction switch through to the
left stop (normal operation: drilling, screwdriving,
etc.).
Left Rotation ( )
Press the rotational direction switch through to
the right stop (for loosening and unscrewing
screws and nuts).
Intended Use
Before Putting into Operation
Changing the Tool
Starting Operation
A
b
a
a
b
2 609 932 475.book Seite 2 Dienstag, 14. Juni 2005 3:05 15
9 • 2 609 932 475 • TMS • 06.06.05
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PSR 14-4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSR 14-4 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info