Manual Bosch PSR 14,4 LI (page 19 of 121) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

78414

Zoom out

Zoom in

1/121

English | 19

Bosch Power Tools 2 609 002 498 | (7.1.08)

Note: The battery is supplied partially charged.

To ensure full capacity of the battery, completely

charge the battery in the battery charger before

using your power tool for the first time.

The lithium ion battery can be charged at any

time without reducing its service life. Interrupt-

ing the charging procedure does not damage the

battery.

The Li-ion battery is protected against deep dis-

charging by the “Electronic Cell Protection

(ECP)”. When the battery is empty, the machine

is switched off by means of a protective circuit:

The inserted tool no longer rotates.

Do not continue to press the

On/Off switch after the ma-

chine has been automatically switched off. The

battery can be damaged.

To remove the battery 6, press the battery un-

locking button 11 and pull the battery out of the

power tool toward the rear. Do not exert any

force.

For charging, the battery 6 can also remain in the

power tool. During the charging procedure, the

power tool cannot be switched on. Press the

On/Off switch 10 to check the charge condition

of the battery, see Section “Battery Charge-con-

trol Indication”.

The battery is equipped with a NTC temperature

control which allows charging only within a tem-

perature range of between 0 °C and 45 °C. A long

battery service life is achieved in this manner.

Observe the notes for disposal.

Changing the Tool (see figure B)

f Before any work on the machine (e. g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational di-

rection switch to the centre position. Unin-

tentional actuation of the On/Off switch can

lead to injuries.

The drill spindle is locked when the On/Off

switch 10 is not pressed. This makes quick, con-

venient and easy changing of the tool in the drill

chuck possible.

Open the keyless chuck 2 by turning in rotation

direction n, until the tool can be inserted. Insert

the tool.

Firmly tighten the collar of the keyless chuck 2 by

hand in rotation direction o until the locking ac-

tion (“click”) is heard. This automatically locks

the chuck.

The locking is released again to remove the tool

when the collar is turned in the opposite direc-

tion.

Replacing the Drill Chuck

(see figures C–E)

f Before any work on the machine (e. g., main-

tenance, tool change, etc.) as well as during

transport and storage, set the rotational di-

rection switch to the centre position. Unin-

tentional actuation of the On/Off switch can

lead to injuries.

The keyless chuck 2 is secured with a securing

screw 13 against unintentional loosening from

the drill spindle. Completely open the keyless

chuck 2 and unscrew the securing screw 13 in ro-

tation direction n. Please note that the securing

screw has a left-hand thread.

If the securing screw 13 is seated tightly, apply a

screwdriver to the screw head and loosen the se-

curing screw by giving a blow onto the handle of

the screwdriver.

Removing the Drill Chuck (see figure D)

Clamp the short end of an Allen key 14 into the

keyless chuck 2.

Place the machine on a stable surface (e.g. a

workbench). Hold the machine firmly and loosen

the keyless chuck 2 by turning the Allen key 14 in

rotation direction n. Loosen a tight-seated key-

less chuck by giving the long end of the Allen key

14 a light blow. Remove the Allen key from the

keyless chuck and completely unscrew the key-

less chuck.

Mounting the Drill Chuck (see figure E)

The keyless chuck is mounted in reverse order.

Note: After mounting the keyless chuck, screw

the securing screw 13 in again.

The drill chuck must be tightened with a

tightening torque of approx. 17–23 Nm.

WARNING

OBJ_BUCH-614-001.book Page 19 Monday, January 7, 2008 1:54 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PSR 14,4 LI in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch PSR 14,4 LI Manual

Product: