387166
14
Zoom out
Zoom in
Previous page
1/77
Next page
14 | English 2 609 002 311 8.5.07
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth
stop 11.
Press the button for the depth stop adjustment 8 and
insert the depth stop into the auxiliary handle 10.
The knurled surface of the depth stop 11 must face
upward.
Pull out the depth stop until the distance between the
tip of the drill bit and the tip of the depth stop corre-
spond with the desired drilling depth X.
Changing the Tool (see figure B)
Keyless Chuck
Hold the rear sleeve 3 of the keyless chuck 1 tight and
turn the front sleeve 2 in rotation direction , until the
tool can be inserted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and
firmly turn the front sleeve 2 in rotation direction by
hand.
Screwdriver Tools
When working with screwdriver bits 13, a universal bit
holder 12 should always be used. Use only screwdriver
bits that fit the screw head.
For driving screws, always position the “Drilling/Impact
Drilling” selector switch 4 to the “Drilling” symbol.
Replacing the Drill Chuck
f For power tools without spindle lock, the drill
chuck must be replaced by an authorised
after-sales service agent for Bosch power
tools.
The drill chuck must be tightened with a
tightening torque of approx. 6–8 Nm.
Operation
Starting Operation
f Observe correct mains voltage! The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Power tools marked with 230 V can also be
operated with 220 V.
Reversing the Rotational Direction
(see figures CD)
The rotational direction switch 7 is used to reverse the
rotational direction of the machine. However, this is not
possible with the On/Off switch 6 actuated.
Right Rotation: For drilling and driving in screws,
push the rotational direction switch 7 left to the stop.
Left Rotation: For loosening and unscrewing screws
and nuts, press the rotational direction switch 7
through to the right stop.
Setting the Operating Mode
Drilling and Screwdriving
Set the selector switch 4 to the “Drilling”
symbol.
Impact Drilling
Set the selector switch 4 to the “Impact
drilling” symbol.
The selector switch 4 engages noticeably and can also
be actuated with the machine running.
Switching On and Off
To start the machine, press the On/Off switch 6 and
keep it depressed.
To lock the pressed On/Off switch 6, press the lock-
on button 5.
To switch off the machine, release the On/Off switch
6 or when it is locked with the lock-on button 5, briefly
press the On/Off switch 6 and then release it.
Adjusting the Speed/Impact Frequency
The speed/impact rate of the switched on power tool
can be variably adjusted, depending on how far the
On/Off switch 6 is pressed.
Light pressure on the On/Off switch 6 results in low
speed/impact rate. Further pressure on the switch
increases the speed/impact rate.
Operating Instructions
f Apply the power tool to the screw/nut only
when it is switched off. Rotating tool inserts can
slip off.
After longer periods of working at low speed, allow the
machine to cool down by running it for approx.
3 minutes at maximum speed with no load.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep the
machine and ventilation slots clean.
If the machine should fail despite the care taken in man-
ufacturing and testing procedures, repair should be
carried out by an after-sales service centre for Bosch
power tools.
OBJ_BUCH-365-001.book Page 14 Tuesday, May 8, 2007 2:47 PM
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch psb 5500 re at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch psb 5500 re in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info