733047
29
Zoom out
Zoom in
Previous page
1/113
Next page
English3
Bosch eBike Systems 0 276 001 SAI | (29.5.15)
Assembly
Inserting and removing the battery pack
For inserting and removing the eBike battery pack in/from the
eBike, please read and observe the battery pack operating in-
structions.
Inserting and removing the on-board computer
(see figure A)
To insert the on-board computer 3, slide it from the front into
the holder 4.
To remove the on-board computer 3, press the lock latch 15
and slide the on-board computer toward the front out of the
holder 4.
Remove the on-board computer when you park the
eBike.
It is possible to secure the on-board computer against remov-
al in the holder. To do so, remove the holder 4 from the han-
dlebar. Put the on-board computer in the holder. Screw the
locking screw 16 (thread M3, 8 mm long) from below into the
thread provided in the holder. Mount the holder back onto the
handlebar.
Checking the Speed Sensor (see figure B)
The speed sensor 17 and its spoke magnet 18 must be
mounted in such a manner that the spoke magnet, after a turn
of the wheel, moves past the speed sensor with a clearance of
at least 5 mm, yet no more than 17 mm.
Note: If the distance between speed sensor 17 and spoke
magnet 18 is too small or too large, or if the speed sensor 17
is not properly connected, the speed indication f will fail, and
the eBike drive unit will operate in emergency mode.
In this case, loosen the screw of the spoke magnet 18 and fas-
ten the spoke magnet to the spoke in such a manner that it runs
past the mark of the speed sensor at the correct clearance. If
the speed is still not being indicated in the speed indication f
after this, please contact an authorised bicycle dealer.
Operation
Initial Operation
Requirements
The eBike system can only be activated when the following
requirements are met:
A sufficiently charged battery pack is inserted (see battery
pack operating instructions).
The on-board computer is properly inserted in the holder
(see “Inserting and removing the on-board computer”,
page English3).
The speed sensor is connected properly (see “Checking
the Speed Sensor”, page English3).
Switching the eBike System On/Off
Options for switching on the eBike system:
If the on-board computer is already switched on when you
insert it into the holder, then the eBike system will be
switched on automatically.
When the on-board computer and the eBike battery pack
are inserted, briefly press the On/Off button 5 of the on-
board computer.
–When the on-board computer is inserted, press the On/Off
button of the eBike battery pack (see battery pack operat-
ing instructions).
The drive is activated as soon as you step on the pedals (ex-
cept when in the push aid feature, see “Switching the Push-
assistance mode On/Off”, page English5). The motor out-
put depends on the settings of the assistance level on the on-
board computer. As soon as the system is activated, “Active
Line” will appear briefly on the display.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25 km/h, the assistance
from the eBike drive is switched off. The drive is automatically
re-activated as soon you start pedaling again and the speed is
below 25 km/h.
Options for switching off the eBike system:
Press the On/Off button 5 of the on-board computer.
Switch the eBike battery pack off by its On/Off button (see
battery pack operating instructions).
Remove the on-board computer out of its holder.
If the eBike is not moved and no button is pressed on the on-
board computer for 10 minutes, the eBike system will shut
down automatically in order to save energy.
eShift (optional)
eShift is the integration of automatic gear shifting systems in-
to the eBike system. To support the rider in the best way pos-
sible, the function indications and the basic settings menu
have been adapted for the “eShift” function.
eShift with NuVinci H|Sync
The optimum gear for the respective speed is automatically
set according to a pre-defined desired cadence. In manual
mode you can choose between multiple gears.
In the NuVinci Cadence” mode you can use the “–” or
“+” button on the operating unit to increase or decrease the
desired cadence. If you hold down the “–” or “+” button, the
cadence will increase or decrease in steps of five. The desired
cadence is shown on the display.
In the “NuVinci Gear mode you can use the “–” or “+”
button on the operating unit to switch back and forth between
several defined transmission ratios. The engaged transmis-
sion ratio (gear) is shown on the display.
OBJ_BUCH-2074-005.book Page 3 Friday, May 29, 2015 7:41 PM
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PowerPack 500 - Intuvia at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PowerPack 500 - Intuvia in the language / languages: English, German, Dutch, French, Italian, Norwegian as an attachment in your email.

The manual is 23,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info