504769

Bosch PLR 50 Manual

20
Zoom out
Zoom in
Previous page
1/128
Next page
20 | English
2 609 140 621 | (18.7.11) Bosch Power Tools
Switching On and Off
To switch on the measuring tool, briefly press the On/Off button 7 or measuring
button 12. When switching on the measuring tool, the laser beam is not switched
on yet.
To switch off the measuring tool, press the On/Off button 7 for a few seconds.
If none of the measuring tool buttons are pressed for approx. 5 minutes, the
measuring tool switches off automatically in order to extend the service life of
the battery.
When a measured value has been stored, it is retained in automatic switch-off
mode. When switching on the measuring tool again, “M” is indicated in the dis-
play.
Measuring Procedure
After switching on, the measuring tool is in the length measurement mode. Other
measuring modes can be switched to by pressing the respective function/mode
button (see “Measuring Functions”, page 20).
After switching on, the rear edge of the measuring tool is preset as the reference
level for the measurement. To change the reference level, see “Selecting the Ref-
erence Level”, page 20.
Upon selection of the measuring function and the reference level, all further
steps are carried out by pushing the measuring button 12.
With the reference level selected, place the measuring tool against the desired
measuring line (e.g. a wall).
Push the measuring button 12 to switch on the laser beam.
f Do not point the laser beam at persons or animals and do not look into the
laser beam yourself, not even from a large distance.
Aim the laser beam at the target surface. Push the measuring button 12 again to
initiate the measurement.
In the tracking function, the measurement already starts upon first actuation of
the measuring button 12.
Typically, the measured value appears after 0.5 and latest after 4 seconds. The
duration of the measurement depends on the distance, the light conditions and
the reflection properties of the target surface. The end of the measurement is in-
dicated by a signal tone. The laser beam is switched off automatically upon com-
pletion of the measurement.
When no measurement has taken place approx. 20 seconds after sighting, the
laser beam is switched off automatically to save the batteries.
Selecting the Reference Level (see figures A–C)
For measuring, you can select between three different reference levels:
– The rear measuring-tool edge (e.g. when measuring onward from a wall),
– The rear positioning-pin edge 14 (e.g. when measuring from a corner),
– The front measuring-tool edge (e.g. when measuring onward from a table
edge).
To change the reference level, press button 9 until the requested reference level
is indicated on the display. Each time after switching on the measuring tool, the
rear end of the measuring tool is preset as the reference level.
Measuring Functions
Length Measurement
For length measurement, push button 1. The indicator for length measurement
appears in the display .
OBJ_DOKU-27449-001.fm Page 20 Monday, July 18, 2011 10:31 AM
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PLR 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PLR 50 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PLR 50

Bosch PLR 50 User Manual - Dutch - 190 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info