110155
27
Zoom out
Zoom in
Previous page
1/168
Next page
English | 27
Bosch Power Tools 1 609 929 N30 | (4.2.08)
Operation
Operating Modes
f Before any work on the machine itself, pull
the mains plug.
Adjusting the Cutting Depth (see figure B)
f Adjust the cutting depth to the thickness of
the workpiece. Less than a full tooth of the
blade teeth should be visible below the work-
piece.
Loosen the clamping lever 24. For a smaller cut-
ting depth, pull the saw away from the base
plate 15; for a larger cutting depth, push the
saw toward the base plate 15. Adjust the de-
sired cutting depth at the cutting -depth scale.
Tighten the clamping lever 24 again.
The tightening tension of the clamping lever 24
can be readjusted. For this, unscrew the clamp-
ing lever 24, and screw it back again turned off-
set by at least 30° in anticlockwise direction.
Adjusting the Cutting Angle
It is best to place the machine on the face side
of the blade guard 17.
Loosen the wing bolts 8 and 16. Tilt the saw
sidewards. Adjust the desired measure on the
scale 7. Tighten the wing bolts 8 and 16 again.
Note: For bevel cuts, the cutting depth is small-
er than the setting indicated on the cutting-
depth scale 25.
Cutting Marks
The 0° cutting mark (11) indicates the position
of the saw blade for right-angled cuts. The 45°
cutting mark (10) indicates the position of the
saw blade for 45° cuts.
For precise cuts, position the circular saw
against the workpiece as shown in the figure. It
is best to carry out a trial cut.
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V
can also be operated with 220 V.
Switching On and Off
To start the machine, first push the lock-off but-
ton for the On/Off switch 1 and then press the
On/Off switch 3 and keep it pressed.
To switch off the machine, release the On/Off
switch 3.
Note: For safety reasons, the On/Off switch 3
cannot be locked; it must remain pressed during
the entire operation.
Reduced starting current (PKS 54 CE/
PKS 66 CE)
The electronic reduced starting current limits
the power consumption when switching the tool
on and enables operation from a 13 ampere
fuse.
Constant Electronic Control (PKS 54 CE/
PKS 66 CE)
Constant electronic control holds the speed
constant at no-load and under load, and ensures
uniform working performance.
Temperature Dependent Overload Protection
(PKS 54 CE/PKS 66 CE)
In case of overload, the machine switches off
until the optimal operating-temperature range is
reached again. Release the On/Off switch 3 and
switch the machine on again to continue work-
ing.
Speed preselection (PKS 54 CE/PKS 66 CE)
The required speed can be preselected with the
thumbwheel 2 (also while running).
The required speed depends on the saw blade
being used and on the material being worked
(see overview of saw blades at the end of these
operating instructions).
0 45
0 45
OBJ_BUCH-662-001.book Page 27 Monday, February 4, 2008 11:14 AM
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PKS 66 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PKS 66 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info