119977
13
Zoom out
Zoom in
Previous page
1/88
Next page
English - 3
Before any work on the machine itself, pull
the mains plug.
Checking the Adjustment of the
Riving Knife
For safety reasons the riving knife 8 must always
be used. The riving knife avoids seizing of the
saw blade while sawing.
The adjustment takes place at the maximum cut-
ting depth.
Loosen the screw 6, adjust the riving knife 8 and
retighten the screw.
Before any work on the machine itself, pull
the mains plug.
To achieve an optimum cut, the saw blade
must not protrude more than 3 mm at the
most from the material.
For adjusting the cutting depth, loosen the
winged screw/clamping lever (PKS 46) 18 and
raise the saw from, or lower it to the base plate 7:
Raise for smaller cutting depths
Lower for greater cutting depths
Set the desired depth on the cutting depth
scale 17.
Tighten winged screw/clamping lever 18 again.
The clamping power of the clamping lever 18 can
be adjusted.
To do this, unscrew the clamping lever and set it
at at least 30° counter-clockwise, screw on again.
Before any work on the machine itself, pull
the mains plug.
Loosen winged screw(s) 5.
Swing the machine to the side until the desired
cutting angle is set on the scale 13.
Tighten winged screw(s) 5 again.
Note: For mitre cutting, the cutting depth is
smaller than the value shown on the cutting depth
scale 17.
The cutting mark 0° ( 16) indicates the position of
the saw blade for right-angled cuts.
The cutting mark 45° ( 15) indicates the position
of the saw blade for 45° cuts.
For an exactly true cut, apply the saw as shown
in the diagrams.
Note: It is best to carry out a trial cut.
Observe correct mains voltage: The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Equipment marked with 230 V can also be con-
nected to 220 V.
Switching On and Off
For starting operation of the machine, actuate
the safety switch against starting 1 first, and then
press and hold the On/Off switch 2 afterwards.
To switch off the machine, release the On/Off
switch 2.
For safety reasons the On/Off switch of
the machine cannot be locked; it must
remain pressed during the entire opera-
tion.
Before Putting into Operation
Adjusting the Cutting Depth
(see figure )
Clamping Lever (PKS 46)
2,5 - 5 mm
2,5 - 5 mm
6
8
C
Adjusting the Cutting Angle
Cutting Marks
Initial Operation
0°45°
0°45°
2 610 392 415 - Buch Seite 3 Dienstag, 10. Dezember 2002 7:52 07
13 • 2 610 392 415 • TMS • 28.11.02
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PKS 46 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PKS 46 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info