21838
12
Zoom out
Zoom in
Previous page
1/64
Next page
English - 4
Before any work on the machine itself, pull
the mains plug.
Be cautious when replacing the planer
blades: Possible danger of injury due to the
sharp cutting edges of the planer blades!
Do not grasp the planer blades by the cut-
ting edges.
Use only original Bosch carbide blades (TC).
The carbide blade (TC) has 2 cutting edges and
can be reversed.
When both cutting edges are dull, the planer
blade must be replaced. The carbide blade (TC)
may not be resharpened.
Disassembling the Planer Blades
(see figure )
To reverse or replace the planer blade, rotate the
blade drum 22 until it is parallel to the planer base
plate 11.
Loosen the two fastening screws 25 with the
Allen key 24 by approx. 1 2 turns.
If necessary, loosen the clamping element 23
by giving it a light blow with a suitable tool
(e. g. a wooden wedge).
Push the planer blade 26 sidewards out of
the blade drum with a piece of wood.
Assembling the Planer Blades
(see figure )
The guide groove of the planer blade always en-
sures continuous height adjustment when replac-
ing or reversing it.
Clean the blade seat (clamping element) and the
planer blade respectively, if required.
When assembling the planer blade, ensure that it
is seated properly in the blade holder of the
clamping element 23 and aligned flush at the side
edge of the rear planer base plate 11.
Afterwards tighten the fastening screws 25
again.
Before restarting, check if the clamping
screws 25 are tightened well.
Rotate the blade drum 22 by hand and en-
sure that the planer blade does not run into
the planer base plate or housing.
Before any work on the machine itself, pull
the mains plug.
Loosen screw 10 and take off the belt cover 9.
Remove worn drive belt 28.
Before assembling a new drive belt, clean both
belt pulleys 27 and 29.
Place the new drive belt on the small pulley 29
first and then work it on the large pulley 27 by
hand while rotating.
Reattach the belt cover 9 and tighten with the
screw 10.
Before any work on the machine itself, pull
the mains plug.
For safe and proper working, always keep
the machine and the ventilation slots clean.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts orders,
please always include the 10-digit order number
given on the nameplate of the machine.
WARNING! Important instructions for con-
necting a new 3-pin plug to the 2-wire cable.
The wires in the cable are coloured according to
the following code:
Do not
connect the blue or brown wire to the
earth terminal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this machine, it must
be disposed of safely.
Replacing the Planer Blade
E
F
Replacing the Drive Belt
(see figure )
Maintenance and Cleaning
G
strain relief
live = brown
neutral = blue
To be fitted
by qualified
professional only
12 • 2 609 932 291 • TMS • 30.01.03
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PHO20_82 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PHO20_82 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PHO20_82

Bosch PHO20_82 User Manual - Dutch, Danish, Swedish, Turkish, Norwegian, Finnish - 106 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info