21838
11
Zoom out
Zoom in
Previous page
1/64
Next page
English - 3
External Dust Extraction
The chip ejector 3 fits on both sides for direct
connection of the Bosch vacuum hose
Ø – 35 mm 19 (accessory). When using other
vacuum hose systems a suitable extraction
adapter may be required.
The vacuum cleaner must be suitable for the ma-
terial to be worked.
When vacuuming dry dust that is especially detri-
mental to health or carcinogenic, use a special
vacuum cleaner.
Integrated Dust Extraction
A chip/dust bag 20 (accessory) can be used for
smaller jobs.
Empty the chip/dust bag regularly. Remove the
chip/dust bag, open the zipper and empty the
chip/dust bag.
Choice of Chip Ejector Side
(Right/Left)
The chip ejector 3 can be switched to the right or
left with the selector lever 6.
Always press the change lever until it engages in
the end position.
The selected ejector direction is marked with an
arrow.
Blade Protector (see figure )
The blade protector 21 allows the machine to be
set down directly after operation, without danger
of damaging the working surface or the planer
blade.
When planing, the blade protector 21 is tilted up-
wards thus enabling full contact of the rear part of
the planer base plate 11.
For stationary use (e. g. with base unit UG 37),
the blade protector must be removed. Press the
blade protector together from the sides and pull it
off.
For non-stationary use, the blade protector
must always be assembled.
Planing
Set the required planing depth and place the front
part of the planer base plate 11 against the work-
piece.
Caution! Danger of kickback!
Apply the machine to the workpiece
only when switched on.
Switch the machine on and guide the machine
with an even feed over the surface to be planed.
To achieve high-grade surfaces, work only with
low feed and apply pressure on the centre of the
planer base plate.
When machining hard materials (e. g. hardwood)
as well as when utilising the maximum planer
width, set only low planing depths and reduce
planer feed, as required. Repeat the planing sev-
eral times.
Excessive feed reduces the surface quality and
can lead to rapid clogging of the chip ejector.
Only sharp blades achieve good cutting capacity
and give the machine longer life.
Beveling Edges (see figure )
The V-grooves 12 in the front planer base
plate 11 allow quick and easy beveling of work-
piece edges. Depending on required bevel width,
use the corresponding V-groove.
For this, place the planer with the V-groove 12
onto the edge of the workpiece and guide along
the edge.
Using the Parallel/Beveling Guide
(Accessory see figure )
Mount parallel guide 13 or beveling guide 17 to
the machine using fastening bolt 14 and rebating
depth stop 2 using fastening bolt 1.
Loosen locking nut 15 and adjust the required re-
bating width with the scale 16. Retighten locking
nut 15 again.
Adjust the required rebating depth accordingly
with the rebating depth stop 2.
Carry out the planing procedure several times,
until the required rebating depth is reached. Pay
attention that the planer is guided with sideward
supporting pressure.
Beveling (only beveling guide 17)
When beveling rebates and surfaces, adjust the
required slope angle with the angle adjust-
ment 18.
Operating Instructions
B
C
D
11 • 2 609 932 291 • TMS • 30.01.03
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PHO20_82 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PHO20_82 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PHO20_82

Bosch PHO20_82 User Manual - Dutch, Danish, Swedish, Turkish, Norwegian, Finnish - 106 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info