97440
18
Zoom out
Zoom in
Previous page
1/105
Next page
1 609 929 N72 | (30.1.08) Bosch Power Tools
18 | English
Reducing the stroke rate is recommended when
the saw blade engages in the material as well as
when sawing plastic and aluminium.
After longer periods of work at low stroke rate,
the machine can heat up considerably. Remove
the saw blade from the machine and allow the
machine to cool down by running it for approx.
3 minutes at maximum stroke rate.
Working Advice
Tips
f When sawing light building materials, ob-
serve the statutory provisions and the rec-
ommendations of the material suppliers.
Note: Do not cover the ventilation slots under-
neath the tool holder with the hand.
Check wood, press boards, building materials,
etc. for foreign objects such as nails, screws or
similar, and remove them, if required.
Switch the machine on and guide it toward the
workpiece. Position the footplate 2 onto the sur-
face of the work and saw through the material ap-
plying uniform contact pressure and feed. After
completing the working procedure, switch the
machine off.
If the saw blade should jam, switch the machine
off immediately. Widen the gap somewhat with a
suitable tool and pull out the machine.
Plunge Cutting (see figures CD)
f The plunge cutting procedure is only suita-
ble for treating soft materials such as wood,
plaster board or similar! Do not work metal
materials with the plunge cutting procedure!
Use only short saw blades for plunge cutting.
Place the machine with the edge of the footplate
2 onto the workpiece and switch on. For power
tools with stroke speed control, set the maxi-
mum stroke speed. Press the power tool firmly
against the workpiece and allow the saw blade to
slowly plunge into the workpiece.
As soon as the footplate 2 fully lays on the sur-
face of the workpiece, continue sawing alongside
the desired cutting line.
Flush Cuts (see figure E)
Using elastic bimetal saw blades, items still at-
tached to a wall (e. g. projecting building ele-
ments such as water pipes, etc.) can be sawn off
flush at the wall.
f Pay attention that the saw blade always ex-
tends beyond the diameter of the material
being worked. There is danger of kickback.
Position the saw blade directly against the wall
and apply some lateral pressure via the tool until
the footplate faces against the wall. Switch the
power tool on and saw through the workpiece,
applying constant lateral pressure.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be
applied alongside cutting line because of the ma-
terial heating up.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
Cleaning the Saw Blade Holder (see figure F)
Clean the saw blade holder preferably with com-
pressed air or a soft brush. Remove the saw
blade from the power tool for this. Ensure proper
operation of the saw blade holder by applying a
suitable lubricant.
Heavy contamination of the machine can lead to
malfunctions. Therefore, do not saw materials
that produce a lot of dust from below or over-
head.
If the machine should fail despite the care taken
in manufacturing and testing procedures, repair
should be carried out by an after-sales service
centre for Bosch power tools.
In all correspondence and spare parts order,
please always include the 10-digit article number
given on the type plate of the machine.
OBJ_BUCH-648-001.book Page 18 Wednesday, January 30, 2008 8:54 AM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PFZ 700 PE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PFZ 700 PE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info