97440
17
Zoom out
Zoom in
Previous page
1/105
Next page
English | 17
Bosch Power Tools 1 609 929 N72 | (30.1.08)
Dust/Chip Extraction
f Dusts from materials such as lead-containing
coatings, some wood types, minerals and
metal can be harmful to one’s health. Touch-
ing or breathing-in the dusts can cause aller-
gic reactions and/or lead to respiratory infec-
tions of the user or bystanders.
Certain dusts, such as oak or beech dust, are
considered as carcinogenic, especially in con-
nection with wood-treatment additives (chro-
mate, wood preservative). Materials contain-
ing asbestos may only be worked by
specialists.
Provide for good ventilation of the working
place.
It is recommended to wear a P2 filter-class
respirator.
Observe the relevant regulations in your coun-
try for the materials to be worked.
Operation
Operating Modes
f Before any work on the machine itself, pull
the mains plug.
Orbital Action Settings
The four orbital action settings allow for optimal
adaptation of cutting speed, cutting capacity and
cutting pattern to the material being sawed.
The level of orbital action can be set with rotary
switch 7, even during operation.
Pivoting Footplate (see figure B)
Due to its movability, the adjustable footplate 2
adapts to the required angular position of the
surface.
Starting Operation
f Observe correct mains voltage! The voltage
of the power source must agree with the
voltage specified on the nameplate of the
machine. Power tools marked with 230 V can
also be operated with 220 V.
Switching On and Off
To start the machine, press the On/Off switch 5
and keep it depressed.
To lock the pressed On/Off switch 5, press the
lock-on button 6.
To switch off the machine, release the On/Off
switch 5 or when it is locked with the lock-on but-
ton 6, briefly press the On/Off switch 5 and then
release it.
Controlling/Presetting the Stroke Rate
Increasing or reducing the pressure on the
On/Off switch 5 enables stepless stroke-rate
control of the switched-on machine.
Light pressure on the On/Off switch 5 results in
a low stroke rate. Increasing the pressure also in-
creases the stroke rate.
When the On/Off switch 5 is locked, it is not pos-
sible to reduce the stroke rate.
With the thumbwheel for stroke rate preselec-
tion 4, the stroke rate can be preset and changed
during operation.
The required stroke rate is dependent on the ma-
terial and the working conditions and can be de-
termined by a practical trial.
Orbital action switched off (level 0):
For working thin or hard material such
as sheet metal or steel.
For achieving clean cutting edges.
Orbital action level I:
For working non-ferrous metals, hard-
wood, plastics or materials of medium
density.
Orbital action level II:
For working with soft materials such
as light building materials, insulation
material, etc.
Orbital action level III:
For working with soft materials such
as soft wood or tree wood.
OBJ_BUCH-648-001.book Page 17 Wednesday, January 30, 2008 8:54 AM
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PFZ 700 PE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PFZ 700 PE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info