78999
19
Zoom out
Zoom in
Previous page
1/105
Next page
English | 19
Bosch Power Tools 1 609 929 M15 | (5.11.07)
Sanding Plate Brake
An integrated sanding plate brake reduces the
stroke rate when running at no-load so that scor-
ing is prevented when placing the machine onto
the workpiece.
If the no-load stroke rate continuously increases
over the course of time, then the sanding plate is
damaged and must be replaced or the sanding
plate brake is worn. A worn sanding plate brake
must be replaced by an authorised after-sales
service agent for Bosch power tools.
Working Advice
f Wait until the machine has come to a stand-
still before placing it down.
Sanding Surfaces
Switch the machine on, place it with the com-
plete sanding surface on the surface to be
worked and move the machine with moderate
pressure over the workpiece.
The removal capacity and the sanding pattern are
mainly determined by the selection of the sand-
ing sheet and the applied pressure.
Only flawless sanding sheets achieve good sand-
ing capacity and extend the service life of the
machine.
Pay attention to apply uniform sanding pressure;
this increases the working life of the sanding
sheets.
Intensifiying the sanding pressure does not lead
to an increase of the sanding capacity, but to in-
creased wear of the machine and the sanding
sheet.
A sanding sheet that has been used for metal
should not be used for other materials.
Use only original Bosch sanding accessories.
Rough Sanding
Attach a sanding sheet with coarse grain.
Apply only light pressure to the machine so that
it runs at a higher stroke rate and high material
removal is achieved.
Fine Sanding
Attach a sanding sheet with fine grain.
By lightly varying the application pressure, the
sanding plate stroke rate can be reduced where-
by the orbital action is maintained.
With moderate pressure, move the machine in a
circular pattern or alternately in lengthwise and
crosswise directions over the workpiece. Do not
tilt the machine to avoid sanding through the
workpiece (e.g. when sanding veneer).
After finishing the working procedure, switch the
power tool off.
Application Table
The data in the following table are recommended
values.
The most favourable combination for working is
best determined by practical testing.
Maintenance and Service
Maintenance and Cleaning
f Before any work on the machine itself, pull
the mains plug.
f For safe and proper working, always keep
the machine and ventilation slots clean.
Application Grain Size
(course sanding/
fine sanding)
Roughening varnish 180/320
Touching up varnish 120/400
Removing varnish 40/80
Softwood 40/240
Hardwood 60/320
Veneer 240/320
Aluminium 80/240
Steel 60/240
Derusting steel 40/120
Stainless steel 120/240
Masonry, stone 80/200
OBJ_BUCH-500-001.book Page 19 Monday, November 5, 2007 8:33 AM
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PEX 220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PEX 220 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info