32131

Bosch PBH200FRE Manual

14
Zoom out
Zoom in
Previous page
1/74
Next page
English–4
1 609 929 F02 • (04.10) T
■ Place the machine on the nut/screw only
when it is switched off.
Auxiliary Handle (Fig. )
■ For safety reasons, the machine should be
used only with the auxiliary handle 14.
By rotating the auxiliary handle 14 to a comfortable po-
sition, a fatigue-free and therefore safe working posi-
tion can be achieved.
Loosen the winged screw 13 on the auxiliary handle
14. Swing the grip to a new position. Retighten the
winged screw.
Overload Clutch
If the insertion tool becomes caught or jammed, the
drive to the drill spindle is interrupted. As a result of the
forces that occur, always hold the machine firmly
with both hands and provide for a sure footing.
Depth Stop (Fig. )
With the depth stop 15, the drilling depth t can be set.
Press the button 12 and pull out the depth stop to the
tip of the drill. Read the value from the scale 22, sub-
tract the desired drilling depth t and set the resulting
value on the depth stop scale.
Dust Vacuuming/Vacuuming Attachment
■ Take protective measures when dust is pro-
duced while working that is detrimental to
health, combustible or explosive. For example:
Some dusts are considered to be carcinogenic. Use
dust/chip extraction and wear a protective mask.
■ Keep your workplace clean. Material mixtures
are especially dangerous. Light metal dust can
burn or explode.
The machine can be connected directly to the socket
of a Bosch all-purpose vacuum cleaner with remote
starting. The vacuum cleaner starts automatically
when the machine is switched on.
Mount the vacuuming attachment (optional accessory)
and connect the vacuum cleaner.
The vacuuming attachment is spring loaded up to the
preselected drilling depth. In this manner, the vacuum-
ing attachment head is always held close to the surface.
Setting the Speed (Fig. )
By increasing or decreasing the pressure on the on/off
switch 8, the speed can be continuously controlled
during operation.
Advantages:
– Slow starting of holes, e.g., on smooth surfaces or
tiles
– No sliding off of the drill when starting the hole
– No splintering of the hole.
Speed Pre-Selection (Fig. )
With the speed regulator 9, the required highest speed
can be pre-set.
As a result of this limitation, the on/off switch can be
pressed only to the pre-set highest speed.
The speed must be selected according to the operat-
ing mode, the material to be worked and the diameter
of the drill.
See Operating Modes for recommended values.
The operation of the gearbox for each application is
set with the mode selection switch 11:
Drilling Hammer Drilling
The operating mode selector switch may be ac-
tuated only at a standstill.
Do not use tools without SDS-plus for hammer
drilling or chiselling!
The following table shows how the operating mode
selector switch 11, the right/left rotation switch 10 as
well as the speed regulator 9 are to be set for the var-
ious operating modes (See fold-out page for figures):
■ Before any work on the machine itself, pull the
mains plug.
■ Always keep the machine and the ventilation slots
clean for proper and safe working.
Clean the tool holder daily.
Working Instructions (Fig. K–N)
K
L
M
Operating Modes (Fig. O–S)
Operating Mode Type PBH
160 RE/
180 RE/
1800 RE/
200 RE
200 FRE
Hammer drilling in
concrete or stone
Fig. Fig.
Drilling in steel or wood Fig. Fig.
Screw driving
Right rotation
Left rotation
Fig.
Fig.
Fig.
Fig.
Chiselling only with MV 200
(optional accessory)
Fig. –
Maintenance and Cleaning
N
O O
P P
R
S
R
S
O
pbh160_bu_1609929F02_t.fm Seite 4 Dienstag, 5. Oktober 2004 11:25 11
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PBH200FRE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PBH200FRE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PBH200FRE

Bosch PBH200FRE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info