32131

Bosch PBH200FRE Manual

13
Zoom out
Zoom in
Previous page
1/74
Next page
English–3
1 609 929 F02 • (04.10) T
The SDS-plus exchangeable drill chuck can easily be
replaced on the rotary hammer with the ring gear ex-
changeable drill chuck provided.
Hammer drilling is possible only with SDS-plus tools
that are inserted in the SDS-plus exchangeable drill
chuck.
Drilling and screwdriving are also possible with tools
without SDS-plus (e.g., round shaft drills, screwdriver
bits) that are clamped in the ring gear exchangeable
drill chuck.
Removing the Exchangeable Drill Chuck
(Fig. )
■ Danger of injury! Before removing the exchangea-
ble drill chuck, always remove the tool or bit.
Grasp the locking ring 6 of the SDS-plus exchangea-
ble drill chuck and pull forcefully in the direction of the
arrow. The exchangeable drill chuck comes off.
Attaching the Exchangeable Drill Chuck
(Fig. )
Take hold of the ring gear exchangeable drill chuck
with the whole hand. Place it with a twisting motion on
the chuck holder until it can clearly be heard to latch.
The exchangeable drill chuck locks itself.
Check locking by pulling on the exchangeable drill
chuck.
Make exchanges in the reverse order in a correspond-
ing manner.
Maintenance of the Exchangeable Drill
Chucks
Keep the connecting parts free of dust. Lubrication is
not necessary.
Take care that the dust protection cap 4 is not
damaged when changing tools.
SDS-plus Tools
The SDS-plus tool is designed to be freely movable.
This causes eccentricity when the machine is off-load.
However, the drill automatically centres itself during
operation. This does not affect drilling precision.
Inserting (Fig. )
Clean and lightly oil the tool before inserting.
Insert the dust-free tool into the tool holder 3 with
twisting until it latches.
The tool locks itself. Check the locking by pulling on
the tool.
Removing (Fig. )
Pull the locking sleeve 5 to the rear (a) and hold while
removing the tool (b).
Tools without SDS-plus
Do not use tools without SDS-plus for hammer
drilling or chiselling!
PBH 160 RE/180 RE/1800 RE/200 RE
To work with tools without SDS-plus (e.g., drills with
cylindrical shafts), a drill chuck 17 with a SDS-plus
chuck shaft 18 (optional accessory) must be inserted
into the tool holder (Fig. ).
Insert the dust-free, assembled chuck into the tool
holder 3 with twisting until it latches (Fig. ).
The chuck locks itself. Check the locking by pulling on
the chuck.
Srewdriver Bits (Fig. )
For screwdriver bits, use the SDS-plus adapter 20 (op-
tional accessory).
PBH 200 FRE
Tool Insertion (Fig. )
Turn the collar of the ring gear exchangeable drill
chuck until the tool holder is opened wide enough. In-
sert the tool and clamp with the drill chuck key 21 uni-
formly in all three holes.
For screwdriver bits, insert a commercially available bit
holder. Insert the screwdriver bits into the bit holder.
Use only screwdriver bits that fit the screw heads.
Screwdriver bits may also be inserted without a bit
holder.
Tool Removal (Fig. )
To remove a tool from the ring gear exchangeable drill
chuck, turn the collar in the direction of the arrow until
the tool can be removed.
System Accessories
Refer to the Bosch Catalogue for insertion tools.
A list of accessories can be found at the end of these
instructions.
Ensure that the mains voltage is correct!
The voltage of the power source must agree with the
value given on the nameplate of the machine. Ma-
chines designated for 230 V can also be operated with
220 V.
Switching On/Off
To switch on the machine, press the on/off switch 8.
Lock the depressed on/off switch 8 by pressing the
lock-on button 7.
To switch off the machine, release the on/off switch
8 or press and then release it.
Changing the Drill Chuck
(PBH 200 FRE)
Tool Changing (Fig. C–I)
A
B
C
D
Putting into Operation
E
F
G
H
I
pbh160_bu_1609929F02_t.fm Seite 3 Dienstag, 5. Oktober 2004 11:25 11
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch PBH200FRE at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch PBH200FRE in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch PBH200FRE

Bosch PBH200FRE User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish - 74 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info