697310
12
Zoom out
Zoom in
Previous page
1/108
Next page
6 720 813 621 (2014/12) MM100
12 | Product details
Determined use
The product must only be used for controlling heating
systems.
Any other use is considered improper. Any damage that may
result is excluded from liability.
Installation, commissioning and maintenance
Installation, commissioning and maintenance must only be
carried out by a suitably qualified engineer.
Only genuine spare parts must be installed.
Electrical work
Electrical work must only be carried out by qualified
electricians.
Before carrying out electrical work:
Isolate all poles of the mains voltage and secure against
reconnection.
Using suitable means, test the power supply is
disconnected.
▶The product requires different voltages.
Do not connect the low voltage side to the mains voltage or
vice versa.
Also observe connection diagrams of other system
components.
Handover to the end user
When handing over the heating system, explain the operating
conditions to the user.
Explain how to operate the heating system, with particular
emphasis on all safety-related actions.
Explain that conversions or maintenance must only be
carried out by a suitably qualified engineer.
Point out the need for inspections and maintenance for
safe and environmentally friendly operation.
The installation and operating instructions must be given to
the end user for safekeeping.
Damage caused by frost
The system can freeze if it is switched off:
Observe the notices regarding frost protection.
Due to the additional functions, e.g. DHW heating or anti-
seizing protection, the system should always be left on.
Correct any faults immediately.
2 Product details
The module is used to activate
A heating circuit with a heating pump; with or without
mixing valve actuator
A cylinder primary circuit with separate cylinder
primary pump and DHW circulation pump (DHW
circulation pump optional).
The module is used to record
The flow temperature in the assigned heating circuit or
the temperature of the DHW cylinder
The temperature at a low loss header (optional)
7716 192 614
The control signal from a temperature switch in the
assigned heating circuit (optional for a heating circuit
without mixer).
In the following, a heating circuit, constant
heating circuit is generally referred to simply
as a heating circuit.
Function
Max. 4 heating circuits with mixer 
without mixer
1)
1) Max. one heating circuit without mixer recommended

Multiple heating circuit
hydraulic connection
low loss header
Buffer cylinder
2)
2) Not shown in the system schematics.

Flow temperature sensor – system (to T0)
(e.g. on low-loss header)

Possible heating circuit
functions
Heating 
Constant heating
circuit
3)
3) For constant flow temperature, e.g. swimming pool or hot
air heating.
Cooling
External signal for heat requirements (to MD1),
heating pump on/off for a constant heating circuit
Cylinder primary circuit 1 or 2
4)
4) DHW cylinder downstream of low loss header.
DHW circulation pump
Table 2 Functions of module in combination with heat pump
( ) or other heat source ( )
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch MM 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch MM 100 in the language / languages: German, Dutch, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 6,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch MM 100

Bosch MM 100 Installation Guide - English, Danish, French, Polish, Swedish, Turkish, Norwegian, Finnish - 116 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info