Manual Bosch LR 60 (page 20 of 253) (All languages)

786509

Zoom out

Zoom in

1/253

20 | English

Then place the measuring rod with the laser receiver at the

other end of the inclined surface at . Ensure that the posi-

tion of the laser receiver on the measuring rod remains un-

changed.

Start CenterFind mode for the axis to which the inclined

surface is aligned. At the end of CenterFind mode, the in-

clination of the surface is shown on the rotary laser.

CenterLock mode (LR65G)

In CenterLock mode, the rotary laser automatically at-

tempts to align the laser beam to the centre line of the laser

receiver by moving the rotation head up and down. In con-

trast to the CenterFind mode, the position of the laser re-

ceiver is continually checked and the inclination of the rotary

laser automatically adjusted. No slope values appear on the

display of the rotary laser.

Alignment is possible for the X‑axis and Y‑axis both when the

rotary laser is in a horizontal position and when it is in a ver-

tical position.

Start CenterLock mode:

Position the rotary laser and laser receiver so that the laser

receiver is situated in the direction of the X-axis or the Y-axis

of the rotary laser. Align the laser receiver so that the re-

quired axis is at a right angle to the reception area(1).

If the laser beam is aligned to both axes, then place a laser

receiver connected to the rotary laser in the direction of the

X- and Y-axis respectively. Each laser receiver must be situ-

ated within the pivoting range of ±8.5% of the rotary laser.

Switch on the rotary laser in rotational operation.

In the settings menu of the laser receiver, the centre function

must be put in CenterLock (CL) mode. When aligning to two

axes of the rotary laser, this applies to both laser receivers.

To start the CenterLock mode for the X‑axis, either press

and hold the CenterFind(17) mode button, or press and

hold the CenterFind(17) mode button, together with the

X‑axis button(16).

To start the CenterLock mode for the Y-axis, press and hold

the CenterFind(17) mode button, together with the Y‑axis

button(15).

Should the laser beam be aligned to both axes at the same

time, CenterLock mode must be started separately on each

laser receiver.

Following the start of CenterLock mode, the rotary head on

the rotary laser moves up and down. During the search pro-

cess, CLX (X‑axis) or CLY (Y‑axis) appears in the text

display(e).

If the laser beam hits the reception area(1) at the height of

the centre line of the laser receiver, the centre line

indicator(h) and the text display(e) LOC will appear. The

CenterLock symbol is displayed on the rotary laser on the

start screen for the corresponding axis.

In the event of changes to the position of the laser receiver

or rotary laser, the inclination is automatically adjusted on

the rotary laser.

uTake great care when working with the CenterLock

mode that rotary lasers and laser receivers are not

moved unintentionally. Incorrect measurements can

arise from the automatic adjustment of the inclination

with every change of position.

Cancelling CenterLock mode:

To cancel or end the CenterLock mode, press and hold the

CenterFind mode button(17). If the laser beam was already

successfully aligned with the centre line of the laser receiver

at this point, the set inclination remains on the rotary laser

even when CenterLock mode is cancelled.

Troubleshooting:

If the laser beam was unable to find the centre line of the

laser receiver within 2min (no matter whether at the start of

the mode or after changes to position), ERR appears in the

text display(e) and all LED direction indicators light up.

Press any button on the rotary laser and one on the laser re-

ceiver to close the error messages. Reposition the rotary

laser and laser receiver so that the laser receiver is situated

within the pivoting range of ±8.5% of the rotary laser. En-

sure that the laser receiver is aligned to the X-axis or Y-axis

so that the laser beam can pass through the reception

area(1) horizontally. Then restart the CenterLock mode.

If both axes of the rotary laser should be aligned to a laser re-

ceiver, the same centre function must be set on both laser

receivers. A combination of CenterLock mode

andCenterFind mode is not possible.

IfCenterFind mode is already set on one axis

andCenterLock mode is started on the other axis,ERR

andCF will appear alternately in the text display(e). Select

CenterLock mode on both laser receivers and re-start the

function.

Anti-strobe protection filter

The laser receiver has electronic filters for strobe light. The

filters protect against, for example, interference from the

warning lights of construction machinery.

Working Advice

Aligning with the spirit level

The laser receiver can be aligned vertically (plumb line) with

the spirit level(7). If a laser receiver is mounted at an angle,

it will give incorrect measurements.

1 609 92A 7M6 | (12.05.2022) Bosch Power Tools

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch LR 60 in the language / languages: All languages as an attachment in your email.

The manual is 11.4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch LR 60 Manual

Product: