764284
32
Zoom out
Zoom in
Previous page
1/356
Next page
32 | English
Problem Possible Cause Corrective Measure
Mower standing on
lawn with the display
switched off
Operational problems Press confirm button for screen to light up, or place
mower in docking station.
Mower does not
charge Battery too hot/cold The mower operates when the battery internal temperat-
ure is between 5°C – 45°C. Allow mower to cool down/
warm up. If the error occurs frequently, the docking sta-
tion should be positioned in the shade.
Docking station not switched on Switch on power supply to docking station. If docking
station does not start, contact your Bosch Service
Centre.
Charging pins corroded Clean the charging pins.
Battery not fitted, incorrectly fitted or in-
correct battery for mower Insert battery correctly (see figure L). Use the appropri-
ate Bosch battery.
Mower out of peri-
meter wire Perimeter wire on a slope Leave 30 cm between the perimeter wire and the slope.
Obstacle near perimeter wire Remove obstacle.
Parts of the lawn area
left uncut Mower requires more cuts to finish garden Allow mower to run for 3 full cuts to cover whole lawn
area. Alternatively use the "Intensive mode" under "Mow-
ing mode".
Time slot not long enough for garden size Increase mowing time slot or:
use “Bosch AUTO” calendar function (with Indego
S500 and M700)
use Bosch “SmartMowing” functionality (with In-
dego S+500 and M+700)
Distance between perimeter wires too
small Increase distance between the perimeter wires to a min-
imum of 75 cm.
Rough mowing conditions Select "uneven ground/low sensitivity" option from menu
item "lawn condition/bump sensor".
Flatten garden/remove/bumps/mark out unsuitable
areas with the perimeter wire – Please follow the instruc-
tions in the Installation Guide.
Grass too long Select "uneven ground/low sensitivity" option from menu
item "lawn condition/bump sensor".
Slopes in garden too steep Ensure mower only operates on slopes of 15 degrees or
less and full garden is not on a slope.
Mower gets stuck in
garden Objects/obstacles not marked out Use the perimeter wire to mark off obstacles where the
mower often gets stuck.
Newly laid turf Allow a few weeks for the soil to settle before using the
mower.
Change setting in menu item "lawn condition / bump
sensor" to low sensitivity / uneven.
After watering, wait as long as possible until you start the
mower.
Mower unintentionally
cuts flowers, etc. or
runs over certain
obstacles
Objects/obstacles below 5cm not marked
out Mark obstacle using perimeter wire leaving 30cm from
object or remove objects/obstacles.
Mower does not ap-
pear to cut logically LogiCut system depends on the garden
conditions. Mower does not necessarily
have to continue in the next uncut area.
Further information can be found on the Installation
Guide.
If behaviour re-occurs often, remap garden.
F 016 L94 038 | (11.11.2020) Bosch Power Tools
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Indego S 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Indego S 500 in the language / languages: All languages as an attachment in your email.

The manual is 5,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info