764284
31
Zoom out
Zoom in
Previous page
1/356
Next page
English | 31
Wire signal Detects the wire signal received from the perimeter wire, indicat-
ing its strength (for Service Agent).
The mower will not receive a wire signal while in the docking sta-
tion.
Troubleshooting
Online Support
http://www.bosch-diy.com/indego-help
Problem Possible Cause Corrective Measure
The LED on the dock-
ing station flashes The perimeter wire is interrupted, too long
or too short. Wire not connected and
mower not in the docking station.
Check that the perimeter wire is not interrupted and is
between 20 and 350 meters in length. Then switch
power supply off and then on again.
Follow instructions in Installation Guide to install the
mower.
Excessive vibrations/
noise Blade bolt loose Tighten blade bolt to torque of 2.5Nm.
Cutting blade damaged/bent Replace cutting blade (see figure J).
Mower not docking
reliably Perimeter wire not properly layed out
around docking station Follow instructions in Installation Guide on layout of peri-
meter wire.
Perimeter wire close to a source of interfer-
ence Remove any excess (e.g. coiled up) perimeter wire
around the docking station.
Change perimeter wire ID in the menu.
Wrong docking station position setting Change setting in the "Advanced" menu.
Mower fails to operate Isolator switch not turned on Remove mower out of docking station, turn isolator
switch on and place mower back into docking station (en-
sure docking station is on – LED lights up green).
Possible clogging Always turn isolator switch off first, then check under-
neath the mower. Clear out as necessary (always wear
protective gloves).
Battery not fully charged Place mower in the docking station to allow to charge.
Docking station must be on.
Grass too long Mow lawn with conventional lawnmower to its lowest
height-of-cut setting before using the mower.
Battery too hot/cold The mower operates when the battery internal battery
temperature is between 5°C – 45°C. Allow mower to
cool down/warm up. If the error occurs frequently, the
docking station should be positioned in the shade.
Bosch Power Tools F 016 L94 038 | (11.11.2020)
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch Indego S 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch Indego S 500 in the language / languages: All languages as an attachment in your email.

The manual is 5,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info