786301
20
Zoom out
Zoom in
Previous page
1/311
Next page
20 | English
Protective guard for cutting
uAlways use the protective guard for cutting (9) when
cutting with bonded abrasives.
uProvide sufficient dust extraction when cutting stone.
The protective guard for cutting (9) is fitted in the same way
as the protective guard for grinding (7).
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (18) is fit-
ted in the same way as the protective guard for grinding (7).
Side handle
uDo not operate your power tool without the side
handle (6).
Screw the side handle (6) on the left or right of the machine
head depending on how your are working.
Low-vibration auxiliary handle
The low-vibration auxiliary
handle reduces vibration,
enabling the tool to be used
safely and more comfort-
ably.
uDo not make any alterations of any kind to the auxili-
ary handle.
Do not continue to use a damaged auxiliary handle.
Hand guard
uAlways fit the hand guard (14) when working with the
cup brush/disc brush (15) or diamond core cutter (20).
Attach the hand guard (14) to the auxiliary handle (6).
Fitting and Removing Abrasive Tools
Follow the special assembly instructions for
X-LOCK application tools.
uPull the plug out of the socket before carrying out any
work on the power tool.
uDo not touch grinding and cutting discs until they have
cooled down. The discs can become very hot while work-
ing.
uOnly use original X-LOCK application tools that carry the
X-LOCK logo. A maintained clamping gauge of max.
1.6mm can only be guaranteed with original X-LOCK ap-
plication tools. A higher clamping gauge can lead to insec-
ure clamping, potentially causing the clamp tool to come
loose.
uX-LOCK application tools do not need additional clamping
flanges or support flanges.
uMake sure that the application tool and the holder are not
deformed and are free from dirt and particles.
Pay attention to the dimensions of the abrasive tools.
Make sure that both X-LOCK catches are open (see figure
below) before fitting the X-LOCK application tool.
If necessary, clean the area between the two X-LOCK
catches.
Fitting the abrasive tool
Place the grinding/cutting/flap disc in a central position
on the X-LOCK holder, parallel to the bearing surface
and with the right side facing up.
Push the disc into the holder.
The disc audibly clicks into place. Do not actuate the
lever (3) when doing so.
(3)
uAfter fitting, check that the edge of the abrasive tool
() is fitted correctly, i.e. is no higher than the refer-
ence surface (). If the edge is higher than the refer-
ence surface, either the holder must be cleaned or the
abrasive tool must not be used.
Before removing the grinding/cutting/flap disc: Make
sure that the power tool has come to a complete stop.
Removing the abrasive tool
Open the lever (3).
The grinding/cutting/flap disc will be released.
The grinding/cutting/flap disc can be removed.
(3) (3)
Cup brushes/disc brushes and fibre discs
uAlways fit the hand guard (14) when working with the
cup brush/disc brush or fibre disc.
1 609 92A 6KC | (21.05.2021) Bosch Power Tools
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWX 9-115 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 9-115 in the language / languages: All languages as an attachment in your email.

The manual is 5.53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info