Manual Bosch GWX 17-125 S (page 23 of 379) (All languages)

786297

Zoom out

Zoom in

1/379

English | 23

Angle grinder GWX 14-125 S GWX 17-125 S

Protection class / II / II

A) Rated no-load speed for the selection of appropriate application tools in accordance with ENIEC62841-2-3. The actual speed is lower for

safety reasons and according to production tolerances.

B) Depends on protective guard((11), (9), (13)) and auxiliary handle((7), (8)) in use

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

GWX 14-125 S GWX 17-125 S

3601GD21.. 3601GD23..

Noise emission values determined according toENIEC62841-2-3.

Typically, the A-weighted noise level of the power tool is

Sound pressure level

Sound power level

UncertaintyK

Wear hearing protection!

dB(A)

102

105

Vibration total values ah (triax vector sum) and uncertainty K determined according toENIEC62841-2-3:

Surface grinding and abrasive cutting:

m/s2

6.3

1.5

5.4

1.5

Disc sanding:

m/s2

3.4

1.5

3.6

1.5

Grinding thin metal sheets or other materials that tend to easily vibrate with a large surface area can cause the noise emission value to increase by

up to 15dB. Suitable, heavy damping mats can reduce the increased noise emissions. Increased noise emissions must be taken into considera-

tion, both for the risk assessment of the noise output and for selecting suitable hearing protection.

The vibration level and noise emission value given in these

instructions have been measured in accordance with a

standardised measuring procedure and may be used to com-

pare power tools. They may also be used for a preliminary

estimation of vibration and noise emissions.

The stated vibration level and noise emission value repres-

ent the main applications of the power tool. However, if the

power tool is used for other applications, with different ap-

plication tools or is poorly maintained, the vibration level

and noise emission value may differ. This may significantly

increase the vibration and noise emissions over the total

working period.

To estimate vibration and noise emissions accurately, the

times when the tool is switched off or when it is running but

not actually being used should also be taken into account.

This may significantly reduce vibration and noise emissions

over the total working period.

Implement additional safety measures to protect the oper-

ator from the effects of vibration, such as servicing the

power tool and application tools, keeping their hands warm,

and organising workflows correctly.

Restart protection

The restart protection feature prevents the power tool from

uncontrolled starting after the power supply to it has been

interrupted.

To restart the tool, set the on/off switch (4) to the off posi-

tion and then switch the power tool on again.

Starting current limitation

The electronic starting current limitation feature restricts the

power of the power tool when it is switched on and enables

operation using a 16 A fuse.

Note: If the power tool runs at full speed immediately after

being switched on, this means that the starting current limit-

ation and restarting protection mechanisms have failed. The

power tool must be sent to the after-sales service immedi-

ately; see the "After-Sales Service and Application Service"

section for addresses.

Constant Electronic control

The Constant Electronic keeps the speed at no load and un-

der load virtually consistent, guaranteeing uniform perform-

ance.

Kickback control

If there is a sudden kickback in the power tool,

e.g. jamming in a separating cut, the power

supply to the motor will be interrupted elec-

tronically.

To restart the tool, set the On/Off switch (4) to the "off" po-

sition and then switch the power tool on again.

Bosch Power Tools 1 609 92A 6A1 | (14.02.2022)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 17-125 S in the language / languages: All languages as an attachment in your email.

The manual is 15.48 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GWX 17-125 S Manual

Product: