Manual Bosch GWX 14-125 (page 25 of 347) (All languages)

786305

Zoom out

Zoom in

1/347

English | 25

uAvoid dust accumulation at the workplace. Dust can

easily ignite.

Operation

uDo not load the power tool so heavily that it comes to a

stop.

uPull the plug out of the socket before carrying out any

work on the power tool.

uExercise caution when cutting slots in structural walls;

see the "Information on structural design" section.

uClamp the workpiece if it is not secure under its own

weight.

uIf the power tool has been subjected to a heavy load,

continue to run it at no-load for several minutes to

cool down the accessory.

uDo not use the power tool with a cut-off stand.

uDo not touch grinding and cutting discs until they have

cooled down. The discs can become very hot while work-

ing.

If the power tool becomes electrostatically charged, the

built-in electronics will switch the power tool off. Press the

on/off switch (4) again to restart the power tool.

Practical advice

Rough grinding

uAlways use the protective guard for grinding(7) when

rough grinding with bonded abrasives.

uNever use cutting discs for rough grinding.

uWhen rough grinding, the protective guard for

cutting(8) or the protective guard for grinding(7)

with a fitted cover for cutting(11) can impact the

workpiece and lead to a loss of control.

The best rough grinding results are achieved with a set angle

of 30° to 40°. Move the power tool back and forth with mod-

erate pressure. This will ensure that the workpiece does not

become too hot or discolour and that grooves are not

formed.

uThe protective guard for cutting(8) or the protective

guard for grinding(7) with a fitted cover for cutting(11)

must be used when using bonded discs which are ap-

proved for cutting and grinding.

Surface grinding with flap disc

uAlways use the protective guard for grinding(7) when

grinding with the flap disc.

The flap disc (accessory) enables you to machine curved

surfaces and profiles. Flap discs have a considerably longer

service life, lower noise levels and lower grinding temperat-

ures than conventional grinding discs.

Surface grinding with sanding disc

uAlways fit the hand guard (16) when working with the

rubber sanding pad (17).

Grinding with a sanding disc can be done without a protect-

ive guard.

See the graphics page for fitting instructions.

Cup brush/disc brush/conical brush

uAlways use the protective guard for grinding(7) when

brushing with disc brushes. Brushing with cup

brushes/conical brushes can be performed without

the protective guard.

uAlways fit the hand guard (16) when working with the

cup brush or conical brush.

uThe wires of the disc brush can get caught on the pro-

tective guard and break, if the maximum permitted di-

mensions of the disc brushes are exceeded.

See the graphics page for fitting instructions.

Cutting Metal

uFor cutting metal with bonded cutting discs or dia-

mond cutting discs, always use the protective guard

for cutting(8) or the protective guard for grinding(7)

with a fitted cover for cutting(11).

uWhen using the protective guard for grinding(7) for

cutting work with bonded cutting discs, there is an in-

creased risk of being exposed to sparks, particles and

disc fragments if the disc breaks.

When carrying out abrasive cutting, use a moderate feed

that is suited to the material being machined. Do not exert

pressure on the cutting disc and do not tilt or swing the

power tool.

Do not attempt to reduce the speed of a cutting disc coming

to a stop by applying pressure from the side.

The power tool must always

work in an up-grinding mo-

tion. Otherwise there is a

risk that it will be pushed

uncontrolled out of the cut.

For best results when cut-

ting profiles and rectangular

tubing, start at the smallest

cross section.

Cutting stone

uFor cutting stone with bonded cutting discs or dia-

mond cutting discs for concrete/stone, always use the

extraction guard for cutting with a cutting guide(23)

or the protective guard for cutting(8) or the protect-

ive guard for grinding (7) with a fitted cover for

cutting(11).

uProvide sufficient dust extraction when cutting stone.

uWear a dust mask.

uThe power tool may be used only for dry cutting/grind-

ing.

uWhen using the protective guard for cutting(8) , the

protective guard for grinding(7) or the protective

guard for grinding(7) with a fitted cover for

cutting(11) for cutting and grinding applications in

concrete or masonry, there is an increased dust load

Bosch Power Tools 1 609 92A 765 | (17.03.2022)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 14-125 in the language / languages: All languages as an attachment in your email.

The manual is 25.6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Bosch GWX 14-125 Manual

Product: