786305
23
Zoom out
Zoom in
Previous page
1/347
Next page
English | 23
uAlways position the protective guard(7) such that the
two cams on the unlocking lever(1) engage in the
corresponding openings on the protective guard(7).
uAdjust the protective guard (7) such that sparking in
the direction of the operator is prevented.
uThe protective guard (7) must only be adjustable
while the unlocking lever (1) is actuated. Otherwise,
the power tool must not be used any more under any
circumstances and must be sent to the after-sales ser-
vice.
Note: The coding cams on the protective guard (7) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
uFor cutting, always use the protective guard for
cutting(8) or the protective guard for grinding (7) to-
gether with the cover for cutting(11).
uProvide sufficient dust extraction when cutting stone.
The protective guard for cutting(8) is fitted in the same way
as the protective guard for grinding(7).
Metal cover for cutting
Fit the metal cover for cutting(11) on the protective guard
for grinding(7) (see figureA): Swivel the tool retainer back
(). Attach the cover(11) to the protective guard for
grinding(7) (). Press the tool retainer firmly into place on
the protective guard(7) ().
To remove the cover (see figureB), press the button on the
tool retainer () and swivel it back (). Remove the
cover(11) from the protective guard(7) ().
Plastic cover for cutting
Attach the plastic cover for cutting(11) to the protective
guard for grinding(7) (see figureC). The cover(11) audibly
and visually engages on the protective guard(7).
To remove the cover (see figureD), unlock the cover(11) on
the left- or right-hand side of the protective guard(7) ()
and remove the cover ().
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (23) is fit-
ted in the same way as the protective guard for grinding (7).
Hand guard
uAlways fit the hand guard (16) when working with the
rubber sanding pad (17) or with the cup brush/conical
brush/diamond annular cutter.
Attach the hand guard (16) to the side handle (5).
Standard auxiliary handle/low-vibration auxiliary handle
Screw the auxiliary handle (5)/(6) on the right or left of the
machine head depending on the working method.
uDo not operate your power tool without the auxiliary
handle(5)/(6).
uDo not continue to use the power tool if the auxiliary
handle (5)/(6) is damaged. Do not make any altera-
tions to the auxiliary handle (5)/(6).
The low-vibration auxiliary
handle (6) reduces vibra-
tion, enabling the tool to be
used safely and more com-
fortably.
Fitting and removing abrasive tools
Follow the special assembly instructions for
X-LOCK application tools.
uPull the plug out of the socket before carrying out any
work on the power tool.
uDo not touch grinding and cutting discs until they have
cooled down. The discs can become very hot while work-
ing.
uOnly use original X-LOCK application tools that carry the
X-LOCK logo. A maintained clamping gauge of max.
1.6mm can only be guaranteed with original X-LOCK ap-
plication tools. A higher clamping gauge can lead to insec-
ure clamping, potentially causing the clamp tool to come
loose.
uX-LOCK application tools do not need additional clamping
flanges or support flanges.
uMake sure that the application tool and the holder are not
deformed and are free from dirt and particles.
Pay attention to the dimensions of the abrasive tools.
Make sure that both X-LOCK catches are open (see figure
below) before fitting the X-LOCK application tool.
If necessary, clean the area between the two X-LOCK
catches.
Fitting the abrasive tool
Place the grinding/cutting/flap disc in a central position
on the X-LOCK holder, parallel to the bearing surface
and with the right side facing up.
Push the disc into the holder.
The disc audibly clicks into place. Do not actuate the
lever (3) when doing so.
Bosch Power Tools 1 609 92A 765 | (17.03.2022)
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWX 14-125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWX 14-125 in the language / languages: All languages as an attachment in your email.

The manual is 25.6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info