119917
43
Zoom out
Zoom in
Previous page
1/46
Next page
English
42
NOTE
If the sleeve is tightened in a state where the clip of
the keyless chuck is opened to a maximum limit, a
click noise may occur. This is the noise that occurs
when the loosening of the keyless chuck is prevented
and is not a malfunction.
CAUTION
When it is no longer possible to loosen the sleeve,
use a vise or similar instrument to secure the bit. Set
the clutch mode between 1 and 11 and then turn the
sleeve to the loose side (left side) while operating the
clutch. It should be easy now to loosen the sleeve.
7. Automatic spindle-lock mechanism
This unit has automatic spindle-lock mechanism for
quick bit changes.
8. Confirm that the battery is mounted correctly
9. Check the rotational direction
The bit rotates clockwise (viewed from the rear side)
by pushing the R-side of the selector button.
The L-side of the selector button is pushed to turn the
bit counterclockwise (See Fig. 10) (The
L
and
R
marks are provided on the body).
10. Switch operation
When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
The rotational speed of the drill can be controlled by
varying the amount that the trigger switch is pulled.
Speed is low when the trigger switch is pulled slightly
and increases as the trigger switch is pulled more.
NOTE
A buzzing noise is produced when the motor is about
to rotate; This is only a noise, not a machine failure.
11. Using the hook
CAUTION
When using the hook, pay sufficient attention so that
the main equipment does not fall. If the tool falls,
there is a risk of accident.
Do not attach the tip tool except phillips bit to the tool
main unit when carrying the tool main unit with the
hook suspended from a waist belt.
Injury may result if you carry the equipment
suspended from the waist belt with sharp tipped
components such as drill bit attached.
The hook can be installed on the right or left side and the
angle can be adjusted in 5 steps between 0° and 80°.
(1) Operating the hook
(a) Pull out the hook toward you in the direction of
arrow (A) and turn in the direction of arrow (B)
(Fig. 11).
(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,
60°, 80°).
Adjust the angle of the hook to the desired position
for use.
(2) Switching the hook position
CAUTION
Incomplete installation of the hook may result in
bodily injury when used.
(a) Securely hold the main unit and remove the screw
using a slotted head screwdriver or a coin (Fig. 12).
(b) Remove the hook and spring (Fig. 13).
(c) Install the hook and spring on the other side and
securely fasten with screw (Fig. 14).
NOTE
Pay attention to the spring orientation. Install the
spring with larger diameter away from you (Fig. 14).
(3) Using the bit holder (Hook with bit holder)
Installing the bit
Slide the bit from the side in the direction of Fig.
15, and then insert firmly until the groove on the
bit locks in the protruded section of the hook.
Removing the bit
Securely hold the main unit and pull out the bit by
holding the tip with your thumb (Fig. 16).
CAUTION
The bit may come loose from the hook and cause
bodily injury when reversing the direction of the bit
as shown in Fig. 15 or when using the driver with the
bit stored incomplete.
Only Hitachi STANDARD ACCESSORIES phillips bit
(No. 2 × 55L; Code No. 318236) may be used. Do not
use other bits since they may come loose.
(4) Using as an auxiliary light (Hook with light)
(a) Press the switch to turn off the light.
If forgotten, the light will turn off automatically
after 15 minutes.
(b) The direction of the light can be adjusted within
the range of hook positions 1 - 5 (Fig. 17).
Lighting time
AAAA manganese batteries: approx. 15 hrs.
AAAA alkali batteries: approx. 30 hrs.
CAUTION
Do not look directly into the light.
Such actions could result in eye injury.
(5) Replacing the batteries
(a) Loosen the hook screw with a phillips-head
screwdriver (No. 1) (Fig. 18).
Remove the hook cover by pushing in the direction
of the arrow (Fig. 19).
(b) Remove the old batteries and insert the new
batteries. Align with the hook indications and
position the plus (+) and minus (–) terminals
correctly (Fig. 20).
(c) Align the indentation in the hook main body with
the protuberance of the hook cover, press the
hook cover in the direction opposite to that of the
arrow shown in Fig. 19 and then tighten the screw.
Use commercially available AAAA batteries(1.5 V).
NOTE
Do not tighten the screw excessively. Such action
could strip the screw threads.
CAUTION
Failure to observe the following can result in battery
leakage, rust or malfunction.
Position the plus (+) and minus (–) terminals correctly.
Replace both batteries at the same time. Do not mix
old and new batteries.
Remove exhausted batteries from the hook
immediately.
Do not discard batteries together with normal trash
and do not throw batteries into fire.
Store batteries out of the reach of children.
Use batteries correctly in accordance with the battery
specifications and indications.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 26-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 26-180 in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch GWS 26-180

Bosch GWS 26-180 User Manual - English - 18 pages

Bosch GWS 26-180 User Manual - English - 261 pages

Bosch GWS 26-180 User Manual - German - 18 pages

Bosch GWS 26-180 User Manual - German - 261 pages

Bosch GWS 26-180 User Manual - Dutch - 18 pages

Bosch GWS 26-180 User Manual - Dutch - 261 pages

Bosch GWS 26-180 User Manual - Danish - 18 pages

Bosch GWS 26-180 User Manual - Danish - 261 pages

Bosch GWS 26-180 User Manual - French - 18 pages

Bosch GWS 26-180 User Manual - French - 261 pages

Bosch GWS 26-180 User Manual - Italian - 18 pages

Bosch GWS 26-180 User Manual - Italian - 261 pages

Bosch GWS 26-180 User Manual - Polish - 18 pages

Bosch GWS 26-180 User Manual - Polish - 261 pages

Bosch GWS 26-180 User Manual - Portuguese - 18 pages

Bosch GWS 26-180 User Manual - Portuguese - 261 pages

Bosch GWS 26-180 User Manual - Swedish - 18 pages

Bosch GWS 26-180 User Manual - Swedish - 261 pages

Bosch GWS 26-180 User Manual - Turkish, Spanish - 18 pages

Bosch GWS 26-180 User Manual - Spanish - 261 pages

Bosch GWS 26-180 User Manual - Norwegian - 18 pages

Bosch GWS 26-180 User Manual - Norwegian - 261 pages

Bosch GWS 26-180 User Manual - Finnish - 18 pages

Bosch GWS 26-180 User Manual - Finnish - 261 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info