119917
42
Zoom out
Zoom in
Previous page
1/46
Next page
English
41
Use Cap Position
Rotating speed selection (Position of the shift knob)
LOW (Low speed) HIGH (High speed)
Machine screw 1 – 22
For 4 mm or smaller diameter
screws.
Driving
Wood screw 1 –
For 8 mm or smaller nominal
diameter screws. (DS18DVB2/
DS14DVB2/DS12DVB2)
For 5.5 mm or smaller nominal
diameter screws. (DS9DVB2)
Wood
For 38 mm or smaller
diameters. (DS18DVB2)
For 36 mm or smaller
diameters. (DS14DVB2)
Drilling
For 32 mm or smaller
diameters. (DS12DVB2)
For 21 mm or smaller
diameters. (DS9DVB2)
Metal
For drilling with a metal
working drill bit.
For 6 mm or smaller
diameter screws.
For 4.8 mm or smaller
nominal diameter screws.
For 24 mm or smaller
diameters. (DS18DVB2)
For 18 mm or smaller
diameters. (DS14DVB2/
DS12DVB2/DS9DVB2)
CAUTION
When changing the rotational speed with the shift
knob, confirm that the switch is off.
Changing the speed while the motor is rotating will
damage the gears.
When setting the shift knob to “HIGH” (high speed)
and the position of the cap is “17” or “22”, it may
happen that the clutch does not engaged and that the
motor is locked. In such a case, please set the shift
knob to “LOW” (low speed).
CAUTION
The selection examples shown in Table 5 should be
considered as general standard. As different types of
tightening screws and different materials to be
tightened are used in actual works proper adjustments
are naturally necessary.
When using the driver drill with a machine screw at
HIGH (high speed), a screw may damage or a bit may
loose due to the tightning torque is too strong. Use
the driver drill at LOW (low speed) when using a
machine screw.
NOTE
The use of the battery EB9H, EB926H, EB930H,
EB1222HL, EB1226HL, EB1230HL, EB1426H, EB1430H,
EB1826HL and EB1830HL in a cold condition (below 0
degree Centigrade) can sometimes result in the
weakened tightening torque and reduced amount of
work. This, however, is a temporary phenomenon,
and returns to normal when the battery warms up.
6. Mounting and dismounting of the bit
(1) Mounting the bit
Loosen the sleeve by turning it toward the left (in the
counterclockwise direction as viewed from the front)
to open the clip on the keyless chuck. After inserting
a driver bit, etc., into the keyless drill chuck, and
tighten the sleeve by turning it toward the right (in
the clockwise direction as viewed from the front)
(See Fig. 9).
If the sleeve becomes loose during operation, tighten
it further.
The tightening force becomes stronger when the
sleeve is tightened additionally.
(2) Dismounting the bit
Loosen the sleeve by turning it toward the left (in the
counterclockwise direction as viewed from the front),
and then take out the bit ect. (See Fig. 9).
Work Suggestions
Wood
Drilling Steel Use for drilling purpose.
Aluminum
Machine screw Use the bit or socket matching the screw diameter.
Driving
Wood screw Use after drilling a pilot hole.
Table 4
If the motor is locked, immediately turn the power
off. If the motor is locked for a while, the motor or
battery may be burnt.
4. The scope and suggestions for uses
The usable scope for various types of work based on
the mechanical structure of this unit is shown in
Table 4.
5. How to select tightening torque and rotational speed
Table 5
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Bosch GWS 26-180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Bosch GWS 26-180 in the language / languages: English, Danish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Bosch GWS 26-180

Bosch GWS 26-180 User Manual - English - 18 pages

Bosch GWS 26-180 User Manual - English - 261 pages

Bosch GWS 26-180 User Manual - German - 18 pages

Bosch GWS 26-180 User Manual - German - 261 pages

Bosch GWS 26-180 User Manual - Dutch - 18 pages

Bosch GWS 26-180 User Manual - Dutch - 261 pages

Bosch GWS 26-180 User Manual - Danish - 18 pages

Bosch GWS 26-180 User Manual - Danish - 261 pages

Bosch GWS 26-180 User Manual - French - 18 pages

Bosch GWS 26-180 User Manual - French - 261 pages

Bosch GWS 26-180 User Manual - Italian - 18 pages

Bosch GWS 26-180 User Manual - Italian - 261 pages

Bosch GWS 26-180 User Manual - Polish - 18 pages

Bosch GWS 26-180 User Manual - Polish - 261 pages

Bosch GWS 26-180 User Manual - Portuguese - 18 pages

Bosch GWS 26-180 User Manual - Portuguese - 261 pages

Bosch GWS 26-180 User Manual - Swedish - 18 pages

Bosch GWS 26-180 User Manual - Swedish - 261 pages

Bosch GWS 26-180 User Manual - Turkish, Spanish - 18 pages

Bosch GWS 26-180 User Manual - Spanish - 261 pages

Bosch GWS 26-180 User Manual - Norwegian - 18 pages

Bosch GWS 26-180 User Manual - Norwegian - 261 pages

Bosch GWS 26-180 User Manual - Finnish - 18 pages

Bosch GWS 26-180 User Manual - Finnish - 261 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info